A home hot water heater contains 40 gal of water. Because of a failure of the heat control, heat is continuously applied to the water in the tank, increasing the temperature and pressure. Unfortunately, the relief valve is clogged and the pressure rises past the maximum pressure of the vessel. At 250 psig the tank ruptures. Estimate the quantity of water flashed

Q: a. A U tube differential manometer containing mercury was used to measure the difference of…

A:

Q: Problem # 3: Friction losses and volumetric discharge through a water piping system The cold-water…

A:

Q: 1.A liquid refrigerant (sg = 1.080) is flowing at a weight flow rate of 23.0 N/h. Required…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: 2.A forktruck is parked on a 12 degree downward slope. If the weight is 8500 lb at point G' and the…

A: Draw FBD

Q: 5- Compare the reading of pitot tube and the reading of anemometer to the measurement of air…

A: An anemometer is a device which is used to evaluate the velocity of the air by counting the number…

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then, Select one:…

A: ANSWER = (a) cavitation will formed.

Q: e height of the water

A:

Q: 7. A horizontal cylindrical triangle boiler, length 2.5 m and radius of base 0.6 m, is being filled…

A:

Q: Calculate the NPSHA in ft for the following configuration of pumping system. (Hint: Use steam tables…

A: Net Positive Suction Head is the pressure margin over vapour pressure at the pump suction nozzle…

Q: Helium (Molecular Weight = 4) is pumped into a 20-ft3 tank until the pressure is 149.7 psia. When…

A:

Q: To avoid cavitation, we must ensure that the local pressure everywhere inside the pump stays: O…

A: What is cavitation in pump and how it formed .

Q: 4. A special oil is to be used in an absorption tower. The preliminary design of the unit requires…

A: A schematic diagram of the given case is Given data, Datum height at section 1, Z1 = 10 ft Length…

Q: Determine the time required for the flow in the pipe system shown below to reach 80% of the maximum…

A: a = area of the valve A = area of the tank velocity of fluid when fluid reached height "h" = 2gh…

Q: (b) Water flows from a pressurized tank through a pipe and rises to the surrounding as shown in…

A: Given, Assumptions: Steady flow Incompressible Frictionless (2) and (3) are exposed to…

Q: there is friction in the piping, which means that an additional pressure equivalent to a height of…

A: In this problem, only height is given so answers will be in terms of parameters. Write the minimum…

Q: When 1,800 l/min flows through a 200 mm diameter pipe, which later is reduced to 100 mm, what will…

A:

Q: 8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter…

A: given data; ⇒flow rate (Q)=10gpm=6.309*10-5m3/s⇒piston diamter (d1)=7 in=0.1778m⇒rod diamter(d2)=5…

Q: A vacuum gauge mounted on a condenser reads 0.56 m Hg. What is the absolute pressure in the…

A:

Q: Provide one question and its solution involving an external flow of fluid .

A:

Q: The head loss due to friction is not proportional to length of the pipe.  Select one: True False

A: The head loss due to friction in a horizontal or vertical or laminar or turbulent flow is given by…

Q: Water at 60°F and one atmosphere is being transferred from tank 1 to tank 2 with a 2-hp pump that is…

A: As per the guidelines I can solve only first three subparts. Repost the other part.

Q: A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe. The capacity is 15 L/s of…

A:

Q: Air leaks slowly to atmosphere from a pressurized tank at 19 bar (gage) and 27°C through a hole of…

A: The gas leaking through a tank either exits the tank at subsonic or sonic flow. When the gas leaks…

Q: QI: Determine the pressure in the pipeline if the atmospheric pressure is 80 kPa.

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: 1) With the below nozzle arrangement, what pressure is needed in the pipe in order to get a nozzle…

A: From the given data,

Q: 3- Discuss the siphon process and what benefit of it?

A:

Q: 4) In a leakage test on a ring main, it was observed that when receiver tank was fully charged to 8…

A:

Q: If the NPSHR is 3m less than the NPSHA you got on question number 2, determine the pump suction…

A:

Q: Define a pump. Explain the working principle of any one of the pumps with neat sketch

A: Pump is a device used to add the energy to the liquids in order to move, raise, compress and deliver…

Q: A compressed air tank in a service station has a volume of 10 ft³. It contains air at 70°F and 150…

A:

Q: d) Determine the internal pressure that is required to open the pressure relief valve. e) Heat is…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Part 1: Analysis of the flow through the fire hose nozzle (Hint: Use the integral form of the…

A: Given: Hose diameter, D = 10 cmOutlet diameter, d = 5 cmOutlet velocity, v = 6 m/s To find: (a)…

Q: of the pump is 70%. Calculate (a) the developed head of the pump and (b) the total power input. (c)…

A: The water flow rate from reservoir is Q2=60 gal/min×0.003785 m3 1 gal×1 s60 min=3.75×10-3 m3/sec.…

Q: Q3 / What would happen if the oil was replaced with water in the steam pump? Explain that.

A:

Q: The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the…

A:

Q: A pressure gauge attached to a pipe is reading 180 kPa at a mountain where the atmospheric…

A:

Q: 2. In oasis Water Company to purify the water, it is flowing through a reducer in a horizontal pipe…

A: diameter of pipe d1 = 35cm diameter of and section piped 2= 25cm. vapour pressure at outlet P2 = 50…

Q: The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank…

A:

Q: 21. Determine the required time for a pressure in a tank to drop from 750 kPa to 440 kPa, if (m° =…

A:

Q: Problem 3 Two pipes are connected by a manometer as shown in Fig. Determine the pressure difference,…

A: It is required to determine pressure difference between A and B

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.