A 800N package is supported by two cables and a rod as shown. 1600mm 600mm. 600mm B 1800mm 1200mm 800mm Which of the following shows the most ideally constructed force diagram of point A? A C D D Z B TAC B FDA TAC FDA TAR A TAB A 800 N 800 N B C D C D B TAC B FDA TAC FDA TAN A 800 N TAN A 800 N

A 800N package is supported by two cables and a rod as shown. 1600mm 600mm. 600mm B 1800mm 1200mm 800mm Which of the following shows the most ideally constructed force diagram of point A? A C D D Z B TAC B FDA TAC FDA TAR A TAB A 800 N 800 N B C D C D B TAC B FDA TAC FDA TAN A 800 N TAN A 800 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P(kN) 53 A 3 3 find S1,52,53,54, S5 Rod forces.indicate that they are tensile or pressure.Write the results you found in the table below. www ww wm w w ROD FORCE TENSİLE/PRESSURE NUMBER S1 S2 S3 S4 S5 5u
21:19 40 A 9 41%- Chegg Home Expert Q&A My answers ( Civil Engineering Question The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point Cto point A (Figure 1) Figure You answered Bo P1 II
Use the following scale for the diagrams: SHEAR DIAGRAM: 1 cm = 100 kN; MOMENT DIAGRAM: 1cm = 100 kN-m F kN Fa kN F kN/m As B DF3 kN-m 1 m 2 m 2 m 2 m R2 3 m 2 m R1 F1 = 72: F2 = 30; F3 = 150;F4 = 60 %3D
Two identical 10 mm diameter A36 steel wires support the rigid beam shown. Determine the maximum load P that can be applied if a Factor of Safety of 2.0 is required. See the text Appendix for any material properties that are needed. E 4 m A -3 m 2 m
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
4 m 450 mm [s0 mn [50 mn 18 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water, helshe stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B8-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 mis?. Provide all steps of your working and solutions handwriten; include diagrams and coordinate systems. a. Determine the reactions at each support A and B. Use the variable w for the weight of the diver, include a free-body diagram.
Two vertical rods AB (A36 steel, E = 200 GPA) and CD (red brass, E = 101 GPA) support a rigid bar AC which is loaded at E. In the current configuration workers in the factory have noticed the horizontal bar AC rotates slightly once the load in E is applied. This is causing problems and needs to be addressed. Your supervisor has asked you to first verify that this rotation is occurring and calculate its magnitude. Then determine the new location for the load application point E such that this rotation can be eliminated.
Situation 10: For the connection shown in the figure. Pu = 100 KN, x1 = 200, x2 = 200, y1= 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 27 KN O 31 KN O 33 KN 0000 O 29.KN O O 1. Which of the following nearly gives the maximum force in the bolt due to the torque alone? x1 10000 x2
D Question 7 A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and has an elongation of 0.009 in. The initial radius of the material is most nearly? O 0.94 in O 0.10 in O 0.31 in O 2.83 in
The plate is suspended using the three cables which exert the forces shown in (Figure 1). Part A Express force FRA as a Cartesian vector. Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. • View Available Hint(s) Figure vec FBA = lb Submit FCA = 500 Ib Part B 14 ft Faa = 350 Ib FDA - 400 Ib Express force FCa as a Cartesian vector. D 3 ft 2ft Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. 3 ft3 ft 6 ft Yiou Ounilablo Hintle)
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
Q.2) A steel plate is subjected to a force system as shown below. Replace the given force system by a resultant force and locate intersection of its line of action with the x-y plane. X-- 45 lb 2.5' 60 lb 4.5' 3' 55 lb 50 lb 2₁- 30 lb 5' 4' 70 lb y