The plate is suspended using the three cables which exert the forces shown in (Figure 1). Part A Express force FRA as a Cartesian vector. Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. • View Available Hint(s) Figure < 1 of 1> vec FBA = lb Submit FCA = 500 Ib Part B 14 ft Faa = 350 Ib FDA - 400 Ib Express force FCa as a Cartesian vector. D 3 ft 2ft Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. 3 ft3 ft 6 ft Yiou Ounilablo Hintle)

The plate is suspended using the three cables which exert the forces shown in (Figure 1). Part A Express force FRA as a Cartesian vector. Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. • View Available Hint(s) Figure < 1 of 1> vec FBA = lb Submit FCA = 500 Ib Part B 14 ft Faa = 350 Ib FDA - 400 Ib Express force FCa as a Cartesian vector. D 3 ft 2ft Express your answer in terms of the unit vectors i, j, and k. Use the 'vec' button to denote vectors in your answer. Express your answer in pounds to three significant figures. 3 ft3 ft 6 ft Yiou Ounilablo Hintle)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hand written an clean solution please
Please solve this question in handwriting step by step .
Please answer asap with clear and complete solution. Thank you
The linkage is made using two A992 steel rods, each having a circular cross section. If each rod has a diameter of 0.85 in .. (Figure 1) Figure 1 12 ft of 1 B 45° 30° Part A Determine the largest load it can support without causing any rod to buckle. Assume that the rods are pin connected at their ends. Express your answer to three significant figures and include the appropriate units. μA Pmax = 354.255 lb ?
A crate with a mass of 250 kg is held in equilibrium by three ropes attached to a steel ring. a d3 d₁ d5 B A 5.5 m 4 m d2 3.5 m 2m d₁ Z 3 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 2 m d₂ d4 a. Determine the magnitude of the force/tension in cord A, TA. b. Determine the magnitude of the force/tension in cord B, TB. c. Determine the magnitude of the force/tension in cord C, Tc. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord A is The magnitude of the force/tension in cord B is The magnitude of the force/tension in cord C' is d5 kN kN kN
The rectangular plate (L,xL,) given below is installed between two rigid walls and is deformed as shown by dashed lines. Determine the shear strain y and Yxy at point A. Use the table given below and your student ID to find the values of L, L, a, and b. L2 A b. L. b L, (mm) (mm) (mm) 150 200.0 3.0 3.0
The shaft is supported by a journal bearing at A and a thrust bearing at B. (Figure 1) Figure -6 ft- 3000 lb 2500 lb 75 lb/ft I pontot, -12 ft 1 of 1 2 ft Part A Determine the normal force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Nc = Submit Part B HÅ Submit Value Part C Request Answer Determine the shear force at a section passing through point C, which is just to the right of the bearing at A. Express your answer to three significant figures and include the appropriate units. Vc = Value μA Units Request Answer ? Units ? Review
Question 29 An A36 angle bar is used as a tension member connected on both legs with 20 mm . Given that s = 60 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
Figure Lat -1 ft-- B 4 ft -1 ft- 1 of 1 Determine the normal force that the 120-lb plate A exerts on the 40-lb plate B. Express your answer to three significant figures and include the appropriate units. NAB = Submit Provide Feedback μA Value Request Answer Units ?
Item 7 The members of the truss are assumed to be pin connected. (Figure 1) Figure 1 of 1 12 ft 44 -16 ft 16 ft P P 16 ft Part A If member AB is an A992 steel rod of radius 2.5 in., determine the maximum load P that can be supported by the truss without causing the member to buckle. Express your answer to three significant figures and include the appropriate units. μА P = Value kip Submit My Answers Give Up ?
SHOW YOUR SOLUTION.
Please write the solution on paper.