A 3-0 overhead line is being supported by four-disc suspension insulators; the potentials across the first and second insulator from the top are 9 kV and 13 kV respectively. Calculate (i) the line voltage (ii) the ratio of capacitance between pin and earth to self-capacitance of each unit (iii) the string efficiency. Ar

A 3-0 overhead line is being supported by four-disc suspension insulators; the potentials across the first and second insulator from the top are 9 kV and 13 kV respectively. Calculate (i) the line voltage (ii) the ratio of capacitance between pin and earth to self-capacitance of each unit (iii) the string efficiency. Ar

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

In an outdoor substation the three bus-bar conductors are supported by units of post type insulators. Each unit consists of a stack of 3 pin type insulators fixed one on the top of the other. The voltage across the lowest insulator is 15kV and that across the next unit is 12kV. Estimate: ratio of mutual to self-capacitance i. the bus-bar voltage of the substation. Efficiency across the string of insulators ii. iii.
Solve it fast plz
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
Find the most economical cross-section of a 3-core distributor cable 250 m long supplying a load of 80 kW at 400 V and 0.8pf lagging for 4000 hours per annum and open circuited for the remainder of the year. The cost of the cable including installation is (15a+25) per meter, where a 'is area of each conductor in cm². The interest and depreciation total 10 per cent and cost of energy wasted is 10% per unit. The resistance per km of conductor of 1 cm² cross-section is 0.173ohms.
GMR calculate
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
A single-core cable working on 66 kV has a conductor diameter of 2 cm and the sheath of inside diameter is 10 cm. If two metallic intersheaths of diameters 5 cm, 8 cm respectively are used for grading the cable.. If the maximum electric stress is the same for each layers. 1- Find the voltage of each metallic intersheaths. 2- Find the thickness of each layers.
Q4: A power distribution station consisting of 100OKVA, 4500V/225V, and 50 cycles per second single-phase core type mutual inductance equipment is to have an approximate electromotive force per turn of 15V and operates witha maximum flux of1.4T. Based on the above scenario justify what will be the values of turns, currents, and cross-sectional area of the core? Analyze the range of load resistance of this equipment. If the load resistances are very high discuss the various methods on its heat reduction process.
What are interpoles, and what is their purpose?
An ac resistance is higher than a dc resistance. True False
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.