V₁ L₁ ic VC₁ C₁ L2 iL ++ (a) Fig. 6-13a C₂ RV Ćuk Converter 6-29. The Ćuk converter of Fig. 6-13a has parameters V = 12 V, D = 0.6, L₁ = 200 μH, L₂ = 100 μH, C₁ = C₂ = 2 μF, and R = 12 2, and the switching frequency is 250 kHz. Determine (a) the output voltage, (b) the average and the peak-to-peak variation of the currents in L₁ and L2, and (c) the peak-to-peak variation in the capacitor voltages. 6-30. The Ćuk converter of Fig. 6-13a has an input of 20 V and supplies an output of 1.0 A at 10 V. The switching frequency is 100 kHz. Determine the values of L₁

V₁ L₁ ic VC₁ C₁ L2 iL ++ (a) Fig. 6-13a C₂ RV Ćuk Converter 6-29. The Ćuk converter of Fig. 6-13a has parameters V = 12 V, D = 0.6, L₁ = 200 μH, L₂ = 100 μH, C₁ = C₂ = 2 μF, and R = 12 2, and the switching frequency is 250 kHz. Determine (a) the output voltage, (b) the average and the peak-to-peak variation of the currents in L₁ and L2, and (c) the peak-to-peak variation in the capacitor voltages. 6-30. The Ćuk converter of Fig. 6-13a has an input of 20 V and supplies an output of 1.0 A at 10 V. The switching frequency is 100 kHz. Determine the values of L₁

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 3PA: You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors...

See similar textbooks

Similar questions

A) A step-up chopper has an input voltage of 220 V and an output voltage of 660 V. if the non-conducting time of the thyristor is 100us. What is the on-time of the thyristor?
1- In a buck DC/DC converter: ton Va = 100 V, R = 80, D ==0.8, f == 20000 Hz, L = 200 μH, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd - İd K C1 ww + Vo
i need Full detailed Steps
5. Determine Leq at terminal a-b the circuit below. Ans.7.778 mH 10 mH 60 mH 25 mH 20 mH a o o b ele 30 mH
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
I need the answer as soon as possible
A buck converter is working in a steady state. The output voltage and the inductor current can be assumed to be ripple-free, The inductor voltage v during Ton is 50V and during Toff is 3OV. Assuming all devices are idea then: What is the input voltage? Answer: 70
Electrical Engineering (25) It seems that a suburant in the negative impedance converter is the one that simulates negativity for a given floating impedance. Explain how the indicated subar- cuit operates.
- Compute voltage peak of the input. Is it equal to what you are expecting base from the setvalues of your VAC source? - Compute voltage peak of the output. Is it equal to what you are expecting base from the setvalues of your VAC source?
BJT Circuit Theory: I have this following circuit but its not producing the correct output. My input is a 0-3.3 V sine wave at 1 kHz. My output at the speaker should also be a 0-3.3 V sine wave, but its giving me the wrong output. How do I fix this circuit using transistor(s) ?
Make a clamper circuit using 500 µF capacitor, silicon diode, and a 100 KΩ resistor connected to a 10 Vpeak sine wave. Draw the output waveform and indicate the amplitude and the time values supported by your solutions. Do these for both positive and negative clamper circuit. Show your circuits first before your solutions and waveforms.
Draw the small signal equivalent circuit of the following circuit. Note that C1 and C2 are large AC coupling capacitors. 5 VIO C1 RF Q1 C2 fem RL Vo