7. The voltage and current of a single-phase ac load are measured and shown in Fig. 1. Find out the following quantities. 1. The frequency of the supply. 2. The rms values of voltage and current. 3. The phase difference between the current and voltage in degrees. 4. The real, reactive, apparent and complex power of the load. 5. The load power factor. 6. The load impedance. 10 V/div, 10 A/div 1 ms/div Figure 1: Voltage and current of a single-phase load -v(t) i(t)

7. The voltage and current of a single-phase ac load are measured and shown in Fig. 1. Find out the following quantities. 1. The frequency of the supply. 2. The rms values of voltage and current. 3. The phase difference between the current and voltage in degrees. 4. The real, reactive, apparent and complex power of the load. 5. The load power factor. 6. The load impedance. 10 V/div, 10 A/div 1 ms/div Figure 1: Voltage and current of a single-phase load -v(t) i(t)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.12P: The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with...

See similar textbooks

Similar questions

AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
Assume that the voltage applied to a load is V = 208- 30° V and the current flowing through the load is I = 5415° A a. Calculate the complex power S consumed by this load. b. Is this load inductive or capacitive? c. Calculate the power factor of this load. d. Calculate the reactive power consumed or supplied by this load. Does the load consume reactive power from the source or supply it to the source?
41. Two ac sources feed a common variable resistive load as shown in figure. Under the maximum power transfer condition, the power absorbed by the load resistance R, is lall 6 2 j8 2 6 2 11020 ( 0706 O9020° (a) 2200 W (b) 1250 W (c) 1000 W (d) 625 W
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
The voltage v(t)=359.3cos(t)volts is applied to a load consisting of a 10 resistor in parallel with a capacitive reactance XC=25. Calculate (a) the instantaneous power absorbed by the resistor, (b) the instantaneous power absorbed by the capacitor. (c) the real power absorbed by the resistor, (d) the reactive power delivered by the capacitor, and (e) the load power factor.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Let a voltage source v(t)=4cos(t+60) be connected to an impedance Z=230. (a) Given the operating frequency to be 60 Hz, determine the expressions for the current and instantaneous power delivered by the source as functions of time. (b) Plot these functions along with v(t) on a single graph for comparison. (c) Find the frequency and average value of the instantaneous power.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Draw the waveform of voltage and current under the following conditions: A current which lags the voltage by 60°. A current which leads the voltage by 60°. A current which is in phase with the voltage
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1