7) in the figure given above, in which direction is the Profile of a Line control applying? Surface 1 A03A 150:3 30t1 Direction 2 Direction 1 2x 15 Surface3 Surface 4 2X R3 Surface 2 Direction 1 Direction 2 Both direction 1 and 2. D None of the above.

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: What is the frictional Force

A:

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: In a machine, the maximum torque transmitted by a shaft exceed by 15 % the actual torque. A power of…

A:

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: You can use a lever to increase force, distance, and speed.  True or false?   (simple machines:…

A: You can use a Class 1 or Class 3 lever to increase the speed of the load, according to where the…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: angular velocity is equal........

A: Angular velocity is equal 2πN60

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: Is this definitely correct? A few calculators online such as BMEP calculators give me a different…

A: Given data:Torque = T = 100 NmEngine is four stroke,so there is one power stroke after two…

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: What are the types of irregular grids ? Support your answers with relevant diagrams

A: An unstructured or irregular grid consists of triangles and quadrilaterals (2D) or tetrahedral,…

Q: 2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: ## Determining the Net Torque on the Wheel (Considering the Image)The image  shows a wheel with…

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: (a) Is positive or negative work done by a constant force F on a particle during a straight-line…

A: given; find work done=?

Q: Define the term work of force?

A: Work of force is defined as the dot product of force and displacement  W=F.S…

Q: in the Atwood's machine,  it is most convenient to choose up as positive for one mass, and down as…

A: Atwood machine is a simple device and it consists of the pulley, two masses connected with a string…

Q: A six inch diameter cylinder with a two inch rod pushes out its full stroke of 20 inches in 1.5…

A: Forward stroke Area : π462-22=25.13 in2 Volume : V=A×L=502.65 in3 Flow rate : Q=Vt=335.1 in3/s…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: (5) In order to forge a pure gold ring, you first need to purchase the gold. The ring design is a…

A: According to Pappus–Guldinus theorem volume can be given as V=Ax2π×yArea of the block as per given…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm…

A:

Q: What are the concentrated forces?

A: Concentrated forces are more a  mathematical idealizations than a realistic. Force applied at a…

Q: What is the degree of freedom of the two questions

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: If drawn on an x-y plane what would it look like?

A: There is a XY plane on which we have to draw a particular graph bwtween the two variables.

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.