An saw blade starts from 9 rad/s and accelerates at 4 rad/s2 and covers 483 rad. Determine the time it takes.

Q: Draw a network diagram of the project that shows which activities follow which other ones, and…

A:

Q: (B): Following costs are incurred by a factory on the production of identical cupboards: Laborers'…

A: Find below about the cost is direct or indirect. Direct cost:- Direct costs can be defined as costs…

Q: :The form milling from the following is

A: Option b is correct.

Q: The resultant of two forces each equal to P and acting at right angles is. (a) P/E (b) P/2 (c) P/22…

A: Those physical quantities which have both magnitude as well as direction.  For example, velocity,…

Q: Q1. Find the heat flow rate through the composite wall as shown in Fig. below. Assume one…

A:

Q: 8.19 Neglecting the effects of fillets and of stress concentrations, deter- mine the smallest…

A: NOTE: According to Bartleybt\y's policy we shall answer only one question so kindly repost the other…

Q: Note: Show all your calculations steps. A 14-m beam is subjected to a load, the shear force follows…

A: The Rankine turbo generator is a device used to generate energy using heat in the form of fluid. For…

Q: Coupled Harmonic Oscillators X, =0 x= x' = 2t Derivative X= x" = 2nd Derivative ki k2 k3 we M A)…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: With the following modifications: Change the first 3m length to 5m (the second 3m length stays the…

A:

Q: A Carnot Refrigerator cycle absorbs heat at 270K and rejects it at 300K. Find the following: 1.Find…

A: Refrigerator is a device which maintains a body temperature lower than the normal temperature or…

Q: amplitude of 50 mm, what is the maximum If the block is moved horizontally rightward from A 12 kg…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: Determine the torque applied to the shaft of gear A when the acceleration of gear B is 25.5 rad/s^2…

A: Given, Angular acceleration of gear B = 25.5  rad/s2. Mass of gear A , ma = 20 kg Radius of…

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: Consider the following showing the three-bar assembly. Nodes 1 and 4 are fixed. At node 2, a…

A: Draw the free-body diagrams of all three elements.

Q: Refrigerant R 134 a enters an adiabatic heat exchanger at 140 kPa with a quality of 40% and a flow…

A: Given Data Working fluid is R134a Inlet condition  P=140 KPa, x=40% hf=27.08 KJ/Kg hfg=212.08 KJ/Kg…

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: A rectangular plane surface 1 m wide and 3 m deep lies in water in such a way that its plane makes…

A:

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Find the ratio for the tool P and Q

A: Given data,  Two tools P and Q have signatures       50-50-60-60-80-300-0 and…

Q: 1. Is it possible to operate a heat engine with only a high-temperature heat reservoir?? 2. Is it…

A: Second law of thermodynamics is related to entropy change, it states that entropy change of universe…

Q: 7-42 C&S In cryogenic equipment, cold air flows in parallel over the surface of a 2-m x 2-m ASTM…

A:

Q: Where did you get the 3 from for the distance of q?

A:

Q: Problem 2.21 An inverted U-tube manometer is connected to two horizontal pipes A and B through which…

A: Manometer is a device used to measure pressure at a point, with the help of balancing one column…

Q: Derive

A:

Q: 15. Determine the friction force if = 0.3 and M = 0.2. (A) 170 N (B) 191 N (C) 850 N (D) 294 N 300 N…

A:

Q: Q1: Write a balanced expression that represents the anaerobic digestion of organic waste products…

A:

Q: First law of Thermodynamics Conservation of Energy- Cycles Instruction: Completer the table and show…

A:

Q: Q3: For an impulse turbine with a two jets of diameter 80mm and a wheel with a mean cup diameter of…

A: given: The number of jets, n = 2 the diameter of jet, D = 1.2 m Mean cup diameter of wheel, D = 1.2…

Q: Find the equivalent spring system constant for the system shown below and write the differential…

A: Given Data:   To Find: (a) Equivalent spring system. (b) Differential equation.

Q: 6. Obtain the dynamic equation of the system given below in terms of the position of mass M. tew…

A: The study of how moving objects act is known as dynamics. The branch of mechanics that analyzes…

Q: A Carnot engine operates between 27 C and 327°C. If the engine produces 300 kJ of work, what is the…

A:

Q: thm Fom

A: given; ⇒AB=DC=16m⇒AD=BC=10m⇒radius of section AFB (R)=8m

Q: ▼ Part A Determine the moment of inertia of the center crank about the axis. The material is steel…

A:

Q: 2 Weight 2500 kg C3 25 kg 10 cm - D: - A hydraulic lift is used to lift a weight as shown in figure…

A: Given Data m1=25 Kg m2=2500  Kg D1=10cm S.G of oil = 0.82

Q: A regenerative cycle operates with steam supplied at 30 bar and 300 °C, and the condenser pressure…

A: Given data as per the question The pressure of steam =30 bar The temperature of steam =300 0c…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.