In drawing process _force is used to reduce the cross sectional area of the workpiece. a. Pushing b. Compressive c. Pulling d. Pushing and Shear

Q: 1. The appropriate punch size for a blanking operation using to perform a cold-rolled steel (half…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: In the drawing operation, technological property weldability is an important parameter. Select one:…

A: Drawing: It is a process in which uses tensile forces is used to stretch metal.

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: Impact velocity equation

A:

Q: The example for forming process is ___________. a. Tempering b. Drawing c. Gas welding d. Die…

A: The example of forming process is drawing in which material goes under plastic deformation.

Q: 25- Which one of the following operation is not a sheet-metal forming process? a) Seaming Deep…

A: It is required to determine which of the following process is not a sheet metal

Q: 2. Write 5 details found on the drawing title block?

A: The bottom right hand corner block in engineering drawing sheet is known as title block. This block…

Q: Statics; working

A:

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: Identify the forming process in which the rectangular shape of the cross section is reduced into…

A:

Q: Calculate stamping force to produce washers (1/2 inch outside diameter, 3/8 inside diameter) from a…

A:

Q: Sheet Forming Processes; V-Bending of Sheets is more expensive than Edge Bending. (T or F) In Metal…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: Buffing is an example of Riveting is an example of

A:

Q: 11) Define the cornering stiffness.

A:

Q: In general, Fair Use allows small sections of a work to qualify for copying so long as the entire…

A: Given:

Q: To show how individual pieces fit together, it is necessary to use larger-scale drawings and section…

A:

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: On a technical drawing, what is the difference in the application of the "cutting plane line" and…

A:

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: An automated blanking and forming line is designed to from 2 mm thick sheet, made from 2024…

A: Given:Material:  Aluminum,  temper   - Elongation at :    - Young’s Modulus: (70 GigaPascals)   -…

Q: ACTIVITY 6: LINE TYPES ft. a Simple Object Dimension line (Thin) 8 cm Extension line 5 mm THK (Thin)

A: Defined the types of lines as follows. Center Lines Extension Lines Dimension Lines Cutting Plane…

Q: When an airplane lands, the wheels of the landing gear first skid over the concrete landing strip…

A:

Q: Open-die forging (upsetting) involves reduction of height of a specimen between two flat dies using…

A: Forging is the forming process in which metal is shaped by applying force using hammer or…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: he end of forging-stroke during impression-die forging is forming of O a. die cavities O b. die…

A: Answer - option (b) - die flash The end of forging-stroke during impression-die forging is forming…

Q: 1- What type of drawing is this (Assembly, detail assembly, detail, pictorial)? And What is the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Slots on the outer surface of work piece. (O ocrinding process. (O Planning process. (O Drilling…

A: The term "machining" refers to a number of material removal procedures in which a cutting tool…

Q: What is the key information that needs to be incuded in a section view on an assembly drawing.…

A: The Answer is below

Q: What type of lines can be used in a drawing to show that part of an object has been removed ?

A: Solution : There are two types of line which are used to show the removed part of an object : Break…

Q: Rocker is an important part related to The starting work piece in steel hot -:which process rolling…

A: Solution:

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: 10)A moving mandrel is used in Wire drawing Tube drawing Metal cutting Forging

A: As per given question  We have to choose correct options and explain

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.