6 in. 15 lb 8 in. 15 lb

Q: The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected to the…

A: The diameter of the shaft is d = 40 mm. The couple acting on the shaft is F = 3 kN. The length of…

Q: Starting with the general linear momentum balance Dr M p v dv = ₁ SS Dt V A F DA + S ● b consider a…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: NPV calculation simulating 20% increase in product cost.

A: PLEASE PROVIDE ME WITH THE QUESTIONS OR A RELEVANT REFERRENCE THAT WILL GUIDE ME  IN HELPING YOU…

Q: 2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the…

A:

Q: Determine the shear force at point C if P = 3.3 kN/m. A C P B -1.5 m-1.5 m-1.5 m-1.5 m-

A: To find: The shear force at point C. Given: The value of force is P=3.3 kN. Free body diagram:

Q: me average

A: The tensile force for the mechanishm is .The diameters of the rod are  and .The diameter of the pin…

Q: The railcar docklight is supported by the 1/8-in. -diameter pin at A. If the lamp weighs 4.1 lb, and…

A:

Q: The steel shafts is made from two segments AB and BC, which are connected together using a fillet…

A:

Q: The double-web girder is construction from two plywood sheets that are secured to wood members at…

A:

Q: The block members have a cross section of 2 in x 2 in is joined by a glued scarf spliced as shown.…

A: The ultimate normal stress on the glue surface is The factor of safety is The cross section…

Q: The bracket is held to the wall using three A-36 steel bolts at B, C, and D Each bolt has a diameter…

A: To findif a force P = 450 lb is placed on the bracket as shown, determine how far s, the top bracket…

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: The yoke-and-rod connection is subjected to a 40 mm 5 kN, tensile force of 5 kN. Determine the…

A:

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: The copper pipe has an outer diameter of 50 mm and an inner diameter of 40 mm. It is tightly secured…

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: The beam is supported by a pin at B and a short link AC. Determine the average shear stress…

A: Step 1:Given data :d=30 mm Step 2:Taking moments about A…

Q: The aluminum bracket A is used to support the centrally applied load of 8 kip. If it has a thickness…

A: Given Data: The centrally applied load is F = 8 kip. Thickness of bracket is t = 0.5 in. Failure…

Q: The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum…

A: Givenn=5d=1inP=10kipst1=34int2=58inw=4in

Q: An assembly is subjected to a torque (710 lb-in). If the allowable shear stress for the material is…

A: Given:Diameter of smaller section = d = 0.75 inDiameter of bigger section = D = 1.5 inTo find:The…

Q: Question 3. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.