Determine the average shear stress developed in pin A of the truss. A horizontal force ofP = 40 KNis applied to joint C. Each pin has a diameter of 25 mm and is subjected to double shear.

Q: P

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P= 5…

A: ∑Mx=0Ta+Tc-3X5=0                           (1) COMPATABILITY,…

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: Determine the diameter of rivet for the eccentrically loaded riveted joint if the permissible shear…

A:

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

A:

Q: 1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts…

A: Given data:- Shear stress (Ifail) =350 MPa Number of bolts=2 Number of shear =2 Factor of safety=3…

Q: 2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the…

A:

Q: me average

A: The tensile force for the mechanishm is .The diameters of the rod are  and .The diameter of the pin…

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

A: GivenP=58kNw=14 kN/mL=3mAy=45.67 kNDy=54.33 kN

Q: The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C ea have…

A:

Q: 1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts…

A:

Q: P a

A: GIVEN DATA- 23.5-mm-diameter pin at A P = 28.36 kN, a = 2.25 m, and b = 6.56 m.

Q: For the given truss system, determine the normal stress in member BE if its cross sectional area is…

A:

Q: Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free…

A:

Q: At point A & C, the beam is pin connected. Therefore, find the average normal stress in the…

A:

Q: The assembly is used to support the distributed load of w=500 lb/ft. determine effort normal in bar…

A: Given Force = 500 lb/ft Bar diameter = 0.4 in Bolt diameter = 0.3 in To find Normal stress in bar…

Q: Determine the required diameter of the bolts if the failure

A: Shear stress:- Stress induced when force is applied parallel to the surface. It is given that, force…

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: Q4/ The aluminum bracket A is used to support the centrally applied load of 8 kip. If it has a…

A: Now draw the free body diagram of bracket,

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

A:

Q: The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the…

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: 1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts…

A: Givenτfail=350MPa=350 N/mm2F.S=3

Q: The joint fastend togather using two bolts with the plate thickness of 5mm. Determine the required…

A: given; shear stress of bolt(τ)=350MPalets take diameter of bolt=dacting load on plate(P)=40KN

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: A 2" diameter pin connects the three links as shown. The links have a 3" by 3" cross- section.…

A:

Q: F AC N H B 4m O P J K L M C D 5m E 3 m

A:

Q: The beam is supported by a pin at Cand by a short link AB. Each pin has a diameter of 12 mm. Assume…

A:

Q: 2. If P = 8 kN, determine the average shear stress in the pins at A, B and C. All pins are in double…

A:

Q: The lever is held to the fixed shaft using the pin AB. If the couple is applied to the lever,…

A: Given figure,  Take a point O in the centre on the line AB.

Q: The wheel on a trolley is held in place on the leg using a 5-mm-radius pin. If the wheel is…

A: The problem is asking for the average shear stress in the pin. Shear stress is a measure of how much…

Q: For the frame shown, determine the minimum bolt diameter at B if the shear stress in the bolt is…

A:

Q: determine the minimum bolt diameter that may be used for this connection.

A:

Q: F The shaft is loaded with two forces as shown and is fixed at A. The strength is defined as the…

A: The given problem involves analyzing the strength of a shaft subjected to two forces and determining…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A:

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a…

A: F1= 11 kN= 11000 N a= 250 mm b= 100 mm c= 90 mm θ= 40∘ Diameter, d= 29 mm Thickness, t= 31 mm   To…

Q: For the clevis connection shown, determine the shear stress in the 19-mm-diameter bolt for an…

A:

Q: The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter…

A: Given: The load, F = 10 kN The diameter of steel rod, D = 12 mm The diameter of steel pin, d = 8 mm…

Q: 1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts…

A: Introduction The allowable stress is the maximum amount of stress that a specimen can withstand…

Q: Problem 7-13: Determine the maximum shear stress in the strut if it is subjected to a shear force of…

A: