The railcar docklight is supported by the 1/8-in. -diameter pin at A. If the lamp weighs 4.1 lb, and the extension arm AB has a weight of 0.6 lb/ft. 3 ft 125 in Part A Determine the average shear stress in the pin needed to support the lamp. Hint:The shear force in the pin is caused by the couple moment required for equilibrium at A.

The railcar docklight is supported by the 1/8-in. -diameter pin at A. If the lamp weighs 4.1 lb, and the extension arm AB has a weight of 0.6 lb/ft. 3 ft 125 in Part A Determine the average shear stress in the pin needed to support the lamp. Hint:The shear force in the pin is caused by the couple moment required for equilibrium at A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the weight of the counterweight W that should be used. Calculate the shear forces and bending moments and draw the diagrams.
The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the beam supports the force of P=230 kN, determine the force developed in each rod. Consider the steel to be an elastic perfectly plastic material.
The structure shown consists of a single member ABCDE with a pin support at A and a roller support at E. Points B and D are at the midpoints of their respective segments. Determine the internal normal force acting on H which are located immediately to the right of B. Take N = 2 kN, O = 5 kN, and P = 5 kN.
Determine the magnitude of the pin force at A. Assume W = 670 lb, a = 5.2 ft, b = 3.5 ft, r = 7 in. r W C Answer: A = i a B A D lb b
The boom DF at the job crane and the column DE have a uniform weight of sw N/m. If the hoist and load weight P N, determine the resultant internal loading in the crane on cross-section through points A, B and C. h2 L1=1 m L2=2 m L3=1 m h1=1 m h2=1.3 m h1 P=540 N Sw=18 N/m D E B L1 L2 A L3 P F
Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in. r W C Answer: A = i a B a A D lb b
The structure is comprised of rigid bars AB and BCD supported by hinges at A and D. A steel rod at C provides additional support to the system. As shown, there is a roller connection between the bars at B. Determine the magnitude of the force P applied as shown if the vertical displacement of point B is limited to 1.5 mm. Neglect the weights of the bars.
2. The steel pipe has a length of L=24 in. If it is fixed at section C and subjected to the horizontal 200-lb force acting on the handle of the pipe wrench at its end, determine the internal loadings at the section A. 10 in. 14 in 200 lb
The bar of negligible weight is supported by two springs,each having a stiffness k = 80 N>m. If the springs are originally unstretched, and the force is vertical as shown,determine the angle theta the bar makes with the horizontal,when the 45-N force is applied to the bar. 1.5 m- 3 m C В 45 N
A 140-lb bucket is suspended from a cable on the wooden frame. Determine the magnitude of the resultant internal normal force (ND) on the cross section at D. Note that A and B are both pin connections. Express your answer in lbs rounded to 3 significant digits. 1 ft 1 ft B 2 ft 30° G 1 ft E A -2 ft- DH C
The man has a mass of 100 kg and center of mass at G. If he holds himself in the position shown, determine the maximum tensile and compressive stress developed in the curved bar at section a–a. He is supported uniformly by twobars, each having a diameter of 25 mm. Assume the floor is smooth. Use the curved-beam formula to calculate the bending stress.
please answer it correctly