5. A stepped shaft is sunjected to torque as shown in Figure. Determine the angle of twist at the free end. Take G=80KN/mm². Also find the maximum shear stress in any step. Hollow Shaft Solid Shaft d, = 100mm d, = 80mm Solid Shaft d= 60mm d = 80mm 2kN-m B 3kN-m 1kN-m 0.3m- 0.4m. 0.5m

5. A stepped shaft is sunjected to torque as shown in Figure. Determine the angle of twist at the free end. Take G=80KN/mm². Also find the maximum shear stress in any step. Hollow Shaft Solid Shaft d, = 100mm d, = 80mm Solid Shaft d= 60mm d = 80mm 2kN-m B 3kN-m 1kN-m 0.3m- 0.4m. 0.5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an allowable shear stress of 51 MPa. Segment (2) is a solid aluminum shaft with an allowable shear stress of 78 MPa. If a torque of Tc = 25700 N-m is applied at C, determine the minimum required diameter of the brass shaft d₁ and the aluminum shaft d2. Tc Answers: d₁ = i √₂ = i (2) с B A mm mm
Q.43 Consider a steel (E = 200 GPa) column hinged on one side and fixed on the other side. Its height is 1.5m and the cross-section is 20 mm x 25 mm. The Euler's critical stress(in N/mm²) is...
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
Please include free body diagrams. Need asap
According to σgüv= 700N/cm2 and tgüv = 100 N/cm2 in the material of the output beam given the loading condition, cross-section and dimensions in the figure; a) Find the largest Q-spread load that can be safely transported. b) Draw a diagram of shear stress in cross-section. (Note: for all odd values, two digits will be taken after the point.)
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on. c) Determine the relative angle of twist o G-70 GPa # * 2m 450 kN.m B
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
The frame supports the distributed load shown. Determine the state of stress acting at points E and D. Show the results on a differential element at this point. 4 kN/m DA -1.5m-15m+ 3 m 1 BA 20 mm 60 mm 20 mm. 5m T D 50 mm
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
1.8
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11000 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 3300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 94 in., b = 22 in., and c = 32 in.