Q9): If the pins D and C are subjected to single shear while pin at A is a double shear. The diameter of pin D and C are 1.5 in while the diameter of pin A is 1 in. Determine the shear stress at pins A,D and C. Also find the stress in the bar DC if its diameter is 0.5 in. 5 ft B |E 3 ft3 ft-3 ft- 600 lb

Q9): If the pins D and C are subjected to single shear while pin at A is a double shear. The diameter of pin D and C are 1.5 in while the diameter of pin A is 1 in. Determine the shear stress at pins A,D and C. Also find the stress in the bar DC if its diameter is 0.5 in. 5 ft B |E 3 ft3 ft-3 ft- 600 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

10/.. find the shear stress in bolts 2 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM LO -O- O 300 mm 8 mm
Two ropes are used to hoist a 610 Ib engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 12 ksi, and the shearing stress in the pin must not exceed 23 ksi. When the hoist is in the position given by: a = 41 in b = 13 ft c = 15 ft find the following: (a \& b) The forces carried in ropes AB and BC (c \& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013Mchas (a) TAB = () Твс !! (c) dAB = (d) d BC %3! (e) d = %3D be sure to include units with your answers I3D
Solve, draw and label the diagram. Show the direction of the equilibrium equation
A vertical load P= 16 KN is applied as shown on member ABC that is held by the 15-mm diameter cable. The pin at the support C is in double shear and its diameter is 20mm. Determine the shear stress at pic C. Express your answer in "MPa" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUT A UNIT IN YOUR ANSWER, only the numerical value is required. * P A B 300 0. 6m C 0. 8m 0.4m
Two ropes are used to hoist a 530 lb engine/transmission assembly as shown. The rope is anchored at C around the center part of the pin shown, causing the pin to experience a state of double shear. There is a frictionless pulley at A. The normal stress in the rope must not be allowed to exceed 15 ksi, and the shearing stress in the pin must not exceed 21 ksi. When the hoist is in the position given by: a = 44 in b = 11 ft c = 19 ft find the following: (a \& b) The forces carried in ropes AB and BC (c l& d) The necessary diameters of ropes AB and BC (e) The necessary diameter of the pin at C 2013 Michael Swanbom (a) TAB = (b) TBC = (c) dAB = (d) dBc = (e) d =
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
The solid rod with radius r=37 mm is subjected to the loading F;=120 kN, F2=38 kN, F3=29 kN. With dimensions a=210 mm and b=330 mm Determine the magnitude of the combined shear stress at point B, given the following: Section Properties: b A=4300.84 mm? |= 1471963 mm A J= 2943925 mm4 Qmax= 33769 mm? B. O 0.310 MPa O 0,007 MPa O 0,620 MPa O 6.615 MPa O 4.805 MPa O 40.147 MPa O 13.176 MPa
Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".
Problem No. 3. The compound shaft has the following properties: Segment 2 G in both Segment 1 Segment 1 pipe segments Segment 2 Torque Shear Outside Wall Outside Wall Tc, in Strain in Diameter Thickness Diameter Thickness kN.m radians Set A 100 210 mm 12.5 mm 142 mm 650 x106 16 mm 44 mm 35 Set B Set C 22 90 Determine the magnitude of external torque TB. Hint, the sheer stress can be written as T = Gy. TB TC (1) (2) B.
Part A The beam is supported by a pin at A and a short link BC. If P = 12 kN , determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 20 mm (Figure 1) Enter your answers separated by commas. vec TA, TB, TC = MPа Figure < 1 of 1 Submit Request Answer Provide Feedback Ne 0.5m 1m 1.5 m 1.5 m
Situation 4. Situation - A wide flange section has the following properties: I= 108 x 106 mm d=300 mm b = 150 mm t₁ = 9 mm t₁ = 12 mm d = 300 mm F₂=0.4F, F, = 250MPa Q@NA=380x103 mm³ a. Determine the allowable shear stress in MPa. b. Determine the shear capacity in kN. c. Determine the safe uniform load in kN/m that the section could carry if length of the beam is 10 m. d. Determine the shear flow at the neutral axis in N/mm. e. Determine the shear flow of the portion of the flange 30 mm from the edge in N/mm.