Q120: Determine the stress in cable shown in the figure if its diameter is 10mm. If the pins at A and C are subjected to double shear determine the shear stress in pins at A and C if their diameter is 15mm. Also, find the bearing stress in the plate in the location attached with pin A if the thickness of plate is 20mm.

Q120: Determine the stress in cable shown in the figure if its diameter is 10mm. If the pins at A and C are subjected to double shear determine the shear stress in pins at A and C if their diameter is 15mm. Also, find the bearing stress in the plate in the location attached with pin A if the thickness of plate is 20mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For the diagram shown, if the load P = 14 kips, determine: a. the normal force in the member Bar BD…

A: Given data: the applied loadP=14 kipsthe diameter of the pin Bd=0.5 intotal length of the beamL=10…

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: The boom supports the two vertical loads, F = 800 N and F2 = 350 N. Neglect the size of the collars…

Q: Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from…

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

Q: The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is…

A: Diameter of pin, d=11 mm=0.011 mBar width, w=60 mm =0.060 mBar thickness, t=10 mm=0.010 mThe average…

Q: A force of 120 lb is applied to the edge of the member shown in the figure below. Neglect the weight…

A: given: P=120 lb Solution: Maximum bending moment is given as : Mmax=P×4.5=120×4.5=540 lb-in

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm the bar thickness (t) = 15 mm. Each…

Q: A cantilevered solid shaft with length of 400-mm and diameter of 150-mm is loaded at its free end as…

Q: The rectangular bar is connected to the support bracket with a 27-mm-diameter pin. The bar width is…

Q: 2: haft shown below, determine the normal and A, including stress concentrations. Then dr and…

A: Given: r=0.0042 m d=0.03 m D=0.033 m P=1500 N M=300 Nm T=250 Nm

Q: The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is…

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

R.
Q120: Determine the stress in
cable shown in the figure if its
diameter is 10mm. If the pins at
A and C are subjected to double
shear determine the shear stress
in pins at A and C if their
diameter is 15mm. Also, find the
bearing stress in the plate in the
location attached with pin A if
the thickness of plate is 20mm.
B.
Cable sling
Clevis
20 m
Savel plate
50 kg 500 N
20mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in the shaft. The shaft has an outer diameter of &0mm and the thickness of the wall of the hollow segment is 10mm. Please note there are two different formula for solid and hollow shaft. 4 kN-m 2 kN m
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
The shears shown are exerting a vertical force on the branch at point E. Find the load in 2-force member AB in N; use + for tension and - for compression. Write the answer with 3 significant digits. Don't write units; the units are N. P 76 N X= 38 mm y 28 mm 70 mm 35 mm 40 mm
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a = 250mm, b = 170mm, c = 80mm, and 0 = 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket A Answers: Tpin B = i Ob= i Bell crank a B b MPa MPa
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
Solve the problems below: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. 600 N 75 mm 5 mm 75 mm -25 mm 600 N
The tube has an inner diameter d; = 20 mm and an outer diameter d, = 22 mm. It is subjected to an internal pressure of 1 MPa and the loads shown below. Determine the stress at point A and draw it on a stress element. 200 mm 400 mm 150 N-m 600 N 1500 N 800 N
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τn⁢t parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.
The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown on the left. Determine the normal and shear stresses at this point on the inclined plane A-B, by drawing a suitable free-body diagram and applying the equations of force equilibrium. A √70° B 5 ksi -20 ksi
The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is w = 75 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 120 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure. Answer: Pmax=
Two solid steel wall supported shafts are connected using the 4 bolt flange. A torque is applied to one side of the bolted connection. Using G = 11.2x10 psi determine the shear stress in the 4" diameter bolts which are on a 2.5" bolt circle diameter. Solve with the applied torque on the left side coupling as shown. Also determine the bolt shear stress if the applied torque was on the other side of the coupling. 1.5 in. 1.25 in. T-350 lb ft 3 ft 2 ft