400 mm- 200 kN 200 kN

Q: how do we know these values if they're not given

A: Below is the answer to your query.

Q: .

A: Find outA. Determine the shear stress component acting on the inclined plane AB. solve the problem…

Q: Determine the magnitude of the maximum shear stress on the stress element for which σx=-87 MPa,…

A:

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given data as per question Diameter of cable AB = 12mm Diameter of cable AC = 10mm Mass = 2 Mg =…

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: *9-68. The thin-walled pipe has an inner diameter of 12 mm and a thickness of 0.6 mm. If it is…

A: The internal pressure is p=3.5 MPa The internal diameter is d=12 mm The thickness of the pipe is…

Q: The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: *8-12. A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as…

A: Given data:- The diameter of the head is d = 450 mm. The thickness of the head is l = 10 mm. The…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given: The mass of the concrete pipe is m=2 Mg. The diameter of the cable AC is d’=10 mm=0.01 m.…

Q: The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip,…

A: Given data:-  the applied force P=1.50 kip diameter 1.5 in To find: The maximum normal stress (ksi)…

Q: al stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.

A:

Q: The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of…

A: Given data: Axial load subjected on the pipe, P = 60 kN. The inner diameter of the pipe, di = 30…

Q: If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress…

A:

Q: Determine the principal stresses in the cantilevered beam at points A and B.

A: Draw sketch of beam and divide shear force into horizontal and vertical components.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.