*8-12. A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown. If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in the glue and the state of stress in the wall of the vessel. - 450 mm --| 10 mm 20 mm Prob. 8-12

Q: 9-38. Determine the distance y to the center of mass of the cone. The density of the material varies…

A:

Q: Question 4 (3 points) R1 R2 + 18 V

A:

Q: The A-36 steel pipe is subjected to the axial loading of P-25 kN Y Part A 30 mm 40 mm Determine the…

A: Introduction When a load is applied, strain is produced; the amount depends on the material's…

Q: 9-13. A spring-supported pipe hanger consists of tuo speings which are originally unstretched and…

A: Calculating displacement on the spring, Calculating the displacement of the steel rod AB and CD,…

Q: F143 Determine the equivalent state of stres on an clement at the same point that represents the…

A: Given data     To determine the equivalent state of stress of the element At the same point…

Q: 5-10 Three bodies with masses of 3, 6, and 7 kg are lo- cated at points (4, -3, 1), (-1, 3, 2), and…

A: The center of mass of an object is the point at which the total mass of the object can be assumed to…

Q: 9-70. Determine the location c and cone.

A: A centroid is nothing but the center of the mass of a uniform density of objects.

Q: 9-39. Determine the principal stresses acting at point B, which is located just on the web, below…

A: To Find: Principal stresses acting at point B.

Q: Draw the free-body diagram for the following problem. The rod shown.

A: Let, HA be the horizontal support reaction at point A, and RA be the vertical support reaction at A.…

Q: 4.2. Verify Eq. (4-10). -=- == =σσ = 011011 (4-10)

A: To verify the equation σx'x' σy'y' -σ2x'y' =σx σyy - σ2xy = σ11σ12we need to confirm that both sides…

Q: Determine the largest weight of the oil drum that the floor crane can support without overturning.…

A: For the largest weight of drum, the crane is about to overturn. It means there will be no contact of…

Q: If F = {400i + 600j - 300k}, determine Mx.

A:

Q: 2-16. A trus is loaded as shown in Fig. P 2-15. Determine the resultant load on the trus. So00 6000…

A: The truss is subjected to the force of 11000 lb downward and 3000 lb upward. So net resultant load…

Q: 5-48 Locate the centroid of the slender rod shown in Fig. P5-48. 200 mm 200 mm *"200 mm

A: Consider the diagram shown below for the slender rod.

Q: P9-4. The rod is subjected to an extemal axial force of 800 N and a uniform distributed load of l100…

A: Given data: The axil force, Fa = 800 N. The uniformly distributed load, w = 100 N/m. Draw the…

Q: *7-36. The pedestal has a triangular cross section as shown. If it is subjected to a compressive…

A: To Find : The stress and sketch the distribution Given : The compressive force is  The free body…

Q: 10-128 Determine the second moments Ix and Iy for the shaded area shown in Fig. P10-128. y = 200x 40…

A: Consider the diagram shown below for the strip of the element in the shaded region.

Q: Determine the friction force at the surface of contact.

A: Part (a) The 500 N can be resolved as,

Q: 5-29 Locate the mass center of the right circular cone shown in Fig. portional to the distance from…

A: Consider a differential circular element of thickness dz at a thickness z from the xy plane as shown…

Q: 5-50* A cylinder with a hemispherical cavity and a con- ical cap is shown in Fig. P5-50. Locate the…

A: Given Data: The radius of the hemispherical cavity, cylinder and cone is R =140 mm. The length of…

Q: The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of…

A: Given data: Axial load subjected on the pipe, P = 60 kN. The inner diameter of the pipe, di = 30…

Q: ۲/۱ العنوان Le olle и برات The pipe shown in figure has a mass of 800kg. Determine the forces acting…

A: As a subject matter expert in Mechanical Engineering, the first step is to identify the forces…