9-13. A spring-supported pipe hanger consists of tuo speings which are originally unstretched and have a stiffness of k- 0 kN/m, three 304 stainless steel rods. AB and CD. which have a diameter of 5 mm, and EF, which has a diameter of 12 mm, and a rigid beam GH. If the pipe and the fluid it carries have a total weight of 4 kN, determine the displacement of the pipe uhen it is attached to the support. is m L75 m 625 mi0.25 in

Q: 200 mm 150 mm 100 mm 200 mm

A:

Q: 2. Using Simpson's 3/8 rule, get the value of the integral below. I 1 -with h= 1/6. dx X + =

A: Given, The interval, h = 1/6

Q: 03 m k= 200 N /m 04m

A: according to the given details in the question.

Q: Aceite Sg 0,86 4 m 0.5 m Longitud: 6 m.

A:

Q: Side fogure shouws a crate (box). d mass m=200 kq is suspended usiog Hie ropes AB Gand AC and AD,…

A:

Q: 1. A VenricAL SHAFT IS SUPPORTICA Bu FRiCTIONeess BEARINGS AT ITS Evoi Poiuts. THE SHAFT IS ROTATING…

A: Given, The maximum shear stress is τmax=50 MPa Pulleys are weightless The Diameter of each pulley is…

Q: Any time you have to climb a ladder, you want the ladder to remain in static equilibrium. At what…

A: solved;

Q: Consider this. If F₁=10N and A₁=1m, what must A2 be for F₂=20N? F₁ A₁ -4- A₂ -la- F₂

A: F1=10N F1=20N A1=1m2

Q: METHOD OF SECTIONS: Can You Please Find F0rce in Member CE and EF using method of sections.

A: Given :   To find :  Force in Member CE and EF using method of sections.

Q: Q14/ The type of the normal stress due to axial force 2 kN applied on the beam is: (Answer is…

A: For solution refer below images.

Q: #3 - The I177 o0 -N body is supported by whels at A which - AU freely without a ffid frictibn ard by…

A:

Q: lateral displacement equation in each segment using coordinates x1 and x2 shown. EI The member is…

A:

Q: equations of the elastic curve for the shaft using the x1 and x2 coordinates. Take El as constant…

A:

Q: Determine the vertical displacement of point B and rotation of point C using double integration…

A:

Q: 16-31. The shaft is supported at A by a journal bearing and at C by a thrust bearing. Determine the…

A: Here the shaft supported at A by journal bearing which means only vertical reaction exists here at…

Q: A cut slope of H = 7 m was excavated in a saturated clay with a slope of angle ß = 45° with the…

A: The data give is, Cut slope height, z = H = 7 m The angle of the slope, ? = 45° Cohesion, c = 60…

Q: Find velocity of the Slidey, wRs and WAR Using Op= 240mm DA= 150 mm R AR =165 mmm RS= 430mm %3D…

A:

Q: The gear motor can develop 1 10 hp when it turns at 300 rev>min. If the shaft has a diameter of 1…

A: Given: The power developed by the gear motor is P=1/10 hp. The angular velocity of the gear motor is…

Q: Find the welouty f flay A=2.1m2 = २० 0[S

A: Introduction : The question is related with fluid mechanics . In this question we are provided with…

Q: Determine the elongation (inch/es) in a bronze helical spring composed of 20 turns of…

A: Given:Number of turns, n=20Diameter of the wire, d=1.0 inDiameter of the spring, D=4 inLoad, P=500…

Q: The pump operates using the motor that has a power of 85 W. If the impeller at B is turning at 150…

A: Given data as per the question Operating power = 85 w diameter of shaft =20 mm ω = 150 revmin we…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: The (1) composite shaft consists of two steel pipes that are connected at flange B and securely…

A: Given data: ◆ The shear modulus of the steel material:  G = 8700 ksi = 8.7 × 106 psi ◆ The torque…

Q: The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in.,…

A: Given: The power of the reducer motor is P=6 hp. The angular velocity of the reducer motor is ω=1200…

Q: The A30 sloel bolf is tightened within a hole so that the eactive torque on the shank AB can be…

A: Given DataT=50N.mt=kx2/3G=75GPa

Q: A pipe made of wood staves is 150 mm internal diameter and subjected to internal pressure of 1 MPa .…

A:

Q: The A-36 solid steel shaft is 2 m long and has a diameter of 60 mm. It is required to transmit 60 kW…

A: Given data: The diameter of shaft, d = 60 mm. The length of shaft, L = 2 m. The power transmits, P…

Q: The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an…

A:

Q: Q14 Find the load .if the load distance 3m and effort distance 10m and effort=300N

A:

Q: Q15/ The sign of the normal stress due to axial force 2 kN applied on the beam is: * (- Answer is (+…

A:

Q: 5. Determine 8g and 0g. Let q = 15 kN/m and L= 6m. B

A:

Q: Determine the equations of the elastic curve for the shaft using the x, and x, coordinates. Take El…

A:

Q: 15ON 50N 100N /m EI 8 midspan F2 6 12 El 8 over hang =

A:

Q: find the longitudinal strtain experienced by the strut it width is 8mm and height is 20mm

A:

Q: In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the…

A: Given: Spring constant of the spring BD→KBD=134 Nm because from the given figure: the initial length…

Q: The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P =…

A:

Q: The 45 mm diameter shaft is made of steel with a tensile strength of 250 MPa. Using the maximum…

A:

Q: Lind the diumeYee of a cineulan

A: