3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x

3rd: A simply supported 12-m span beam, 300-mm wide by 550-mm deep, is pre- stressed by straight tendons with Aps = 774 mm² located 70 mm from the bottom at an initial prestress of 1.10 GPa. What maximum service uniform live load can the beam support in addition to its own weight if allowable tensile stress in concrete 0.5 x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume straight line instead of parabola for stress-strain curve of concrete as follows and partial factor of safety as 1.0. 0.002 0.67 0.0035 Strain A rectangular under-reinforced concrete section of 300mm width and 500mm effective depth is reinforced with 3 bars of grade Fe 415, each of 16m diameter. Concrete mix is M20. The depth of the neutral axis from the compression fibre is
Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 10 ft 9 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. Pmax = Submit 04 μA Provide Feedback Value Request Answer Units ?
In the design of beam for the limit state of collapse in flexure as per IS 456 : 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis
RCC.
Given the following properties of beam: b = 250 mm, d = 325 mm and h = 400 mm. a) Assuming the concrete is uncracked, compute the bending stresses (in MPa) in the extreme fibers of the beam at M = 100 kN-m. Blank 1 b) Determine the cracking moment (in kNm) for the section if f'c = 28 MPa. Blank 2 c) Compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M = 100 kN-m, n = 9 and reinforced with 5-16 mm diameter tension bars. Unit must be in MPa. fc = _Blank 3, fs =__________ Blank 4
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
Pre-stressed.
I need the answer quickly