The properties of the reinforced concrete T-beamare bi = 30 in., hi = 4 in., b2 = 12 in., h = 18 in.,Ast = 4.5 in?, and n=8. Using elastic analysis,find the maximum stress in the concrete producedby an 80-kip-ft bending moment.h1h2A« (total area)10,606.391 psiO 343.813 psiO 543.318 psi687.954 psi

Calculate the centroidal distance of the reinforced T-beam using the equation of first moment of the…

Answered: s of the reinforced concrete T-beam ,hi…

s of the reinforced concrete T-beam ,hi = 4 in., b2 = 12 in., h2 = 18 in., and n = 8. Using elastic analysis, num stress in the concrete produced a bending moment. hi h2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The properties of the reinforced concrete beam are b = 300 mm, d = 480 mm, Ast = 1306 mm2, and Est /…

A: Given data: b=300 mmd=480 mmAst=1306 mm2m=10σc=16.7 MPaσs=104.8 MPa Assuming cover as 20 mm D=500 mm…

Q: A rigid steel plate is supported by three posts of high-strength concrete each having an effective…

Q: Problem No. 2: The cross-section of the 8-m long simply supported beam is shown below. If the…

A: The given values and diagram is shown below, Beam length=8m longf'c=21MPafy=414MPaUnit weight…

Q: . Calculate the cracking moment (max. resisting moment) for the unreinforced concrete beam shown.…

A: As per Bartleby's guidelines we are supposed to answer only first question.

Q: For the below given beam: a) Determine the cracking distributed load. b) Determine the stress in…

A: Given data : WDL = 15 kN/m WLL = 10 kN/m Materials = C25:S420 A problem of R.C.C

Q: A reinforced concrete beam has a width of 300 mm, an effective depth of 500 mm and is reinforced…

Q: Fc'=28MPa Mmax=+320 kNm Determine the ff: 1. Cracking moment (kNm) 2. Compress stress felt by…

A: Since you have posted a question with multiple sub-parts, we will solve first three subpartsfor you.…

Q: A 1.8 m high square concrete column with b = 220 mm (Ec ac = 9.9 × 10-6/° C) is reinforced with six…

Q: A singly reinforced rectangular concrete beam has a width of 150 mm and an effective depth of 330…

A: Given data: Beam width, b=150 mm. Effective depth, d=330 mm. The characteristics compressive…

Q: Given the following properties of a rectangular concrete beam: b = 300mm, d = 425mm, f'c = 28 MPa,…

Q: A pre-tensioned rectangular concrete beam 150 mm wide and 300 mm depth is prestressed with three…

A: Given- A pre-tensioned rectangular concrete beam, Width b= 150 mm, Depth d= 300 mm, Cross-sectional…

Q: mm- the Beam must carry a Service Calculate the Flexural Stress in the concrete using…

A: GIVEM m= 8 and area od concrete =total area - area of steel

Q: A concrete beam of rectangular cross-section of 200 mm x 400 mm is pre-stressed with a force 400 kN…

Q: 2.3.2 If the beam section of Prob. 2.2.3 is reinforced with 3-25 mm diameter steel bars in the…

A: Given Data: fc = 30mpa 3-25 mm dia steel 65mm from the extreme fiber

Q: prestressed concrete beam has the following characteristics: a width of 300mm overall depth of…

Q: 3.)A reinforced concrete beam 300 mm width has an effective depth of 450 mm. it is reinforced with…

A: Width of beam =300 mm, Depth of beam =450 mm, Area of steel in tension side(As1)=6-32 mm ϕ or…

Q: Consider the prestressed concrete beam and prestressing steel stress-strain diagram given below. The…

A: Given- Ultimate strain capacity - 0.003 in/in Concrete strength - 4000 psi Fse - 137 ksi Ec - 3850…

Q: 1.A. What is the total area of the section * O 70,000 sq. mm O 50,000 sq. mm 60,000 sq. mm O other:

A: A cross section of I-beam is given. We need to find out the Total area of the section.

Q: 1. A steel section of length L sits on an 8" x 8" bearing plate. The bearing plate is perfectly…

A: To determine,A. Determine the normal stress in the steel. B. Determine the normal stress in the…

Q: 1) A rectangular reinforced concrete beam with dimensions b = 14 in, d = 25 in, and h = 28 in is…

Q: A rectangular concrete beam of width 120 mm and depth 200 mm is prestressed by pre-tensioning to a…

Q: (3) for Normal weight Concrete, using ACI Code and recommendation for high strength concrete, to…

A: Solving first questionGiven datacompressive strength of concrete given in table findmodulus of…

Q: 2. (a). Determine the cracking moment for the beam section shown. Use fc = 21 MPa. (b). What is the…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: In a given reinforced concrete beam, b=300mm, d= 600mm and n=9. If a maximum stress of 5MPA is…

A: Given: Assume m=13.33

Q: Question A concrete beam of rectangular cross-section of 200 mm x 400 mm is pre-stressed with a…

A: GivenCross-section-It is needed to find the maximum compressive stress in the concrete.

Q: Two rectangular wood panels is formed by joining two boards together using high strength adhesive in…

A: Limit to normal stress for glue = 4.83 MPa. limit to shear stress for glue = 3.10 MPa. working…

Q: determine the maximum and concrete and steel stresses at the point of maximum positive and negative…

A: Maximum bending stress The top surface of the die experiences the most bending stress, which…

Q: The properties of the reinforced concrete beam are b = 310 mm, d = 467 mm, Ast = 1173 mm2, and Est /…

A: Bending Moment is 57.20 x 103 Nm or 57.2 KN-M.

Q: 1.B. Compute for the total Ig of the section O 100,000,333 mm^4 O 108,333,333.33 mm^4 133,333,333.33…

A: Rotational inertia, the rotational counterpart of mass for linear motion, is known as the moment of…

Q: A pre-tensioned rectangular concrete beam 200 mm wide and 350 mm depth is prestressed with three…

Q: The properties of the reinforced concrete beam are b = 306 mm, d = 467 mm, Ast = 1007 mm2, and Est /…

Q: Q.2 Flexural Formula In a reinforced concrete section, the stress at the extreme fibre is…

A: Given data- A reinforced concrete section- Stress at compression side f =5.80 MPa, Depth of NA y =58…

Q: A concrete beam of rectangular cross-section of 200 mm × 400 mm is prestressed with a force of 400…

A: Given a concrete beam with rectangular cross sectional area. The eccentric prestressing force can be…

Q: A round concrete column has a diameter D.A force of 800 kN act on the column as shown. The yield…

A: Diameter = 50.46 mm

Q: The maximum compressive stress in a beam is 6 MPa. The depth of neutral axis of the beam is 60 mm…

A: Given: Maximum compressive stress, σ = 6 MPa Depth of neutral axis, y = 60 mm Compressive strength…

Q: In a reinforced concrete section, the stress at the extreme fibre is compression is 5.80 MPa. The…

Q: A cylindrical block of concrete is 300mm long and has a circular cross section of 100mm in diameter.…

Q: Problem 4.35 A Part A Column AB is made from high strength pre-cast concrete and reinforced with…

Q: (e) Compute the flexural stresses. Compressive stress of concrete at the top of the beam and tensile…

Q: 3. Analyze the composite structure shown. a. Determine the axial force on member AB b. Determine the…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

100%

The properties of the reinforced concrete T-beam
are bi = 30 in., hi = 4 in., b2 = 12 in., h = 18 in.,
Ast = 4.5 in?, and n=8. Using elastic analysis,
find the maximum stress in the concrete produced
by an 80-kip-ft bending moment.
h1
h2
A« (total area)
10,606.391 psi
O 343.813 psi
O 543.318 psi
687.954 psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

e. Before loading, the concrete shrinks &z-conc = 0.05 (0.5%). This is less than if it were not restrained by “temperature steel", so the downdrag preloads the steel ơ2-0 = 3,000 psi. When the P = 200K is applied, estimate the final stress in the steel. %3D %3D
i need the answer quickly
PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) 6-25mm diam. b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa)
Given the following properties of beam: b=250mm, d=325mm and h=400mm a. Assuming the concrete is uncracked, compute the bending stresses in the extreme fibers of the beam at M=25 kN-m b. Determine the cracking moment for the section if f'c=21MPa c. compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M=25knm, n=9 and reinforced with 4-16mm diameter tension bars
Problem 2.7 A reinforced concrete beam has the following data. Beam width, b= 300 mm Effective depth, d= 600 mm Compression steel cover, d'= 60 mm Concrete strength, fc=27.5 MPa Steel Strength, fy= 415 MPa a) Find the flexural strength of a singly-reinforced section if the extreme tension steel reached a strain of 0.005. b) Find the mumber of pieces of 28 mm diameter flexural steel for a singly-reinforced section if the extreme tension steel reached a strain of 0.005. c) Find the mumber of 28 mm diameter tension reinforcements if the section is to resist a factored design load of 660 kN-m d) If 2-28 mm diameter bars are added as compression steel, detemine the maximm mumber of pieces required for the tension reinforcements. Assume the compression steel yielded and ignore displaced concrete.
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moments. Reinforced Concrete Design
In a reinforced concrete section, the stress at the extreme fibre is compression is 5.80 MPa. The depth of neutral axis in the section is 58 mm and the grade of concrete is M25. Assuming linear elastic behavior of the concrete, the effective curvature of the section (in per mm) is
A rectangular beam has a width of 380 mm, effective depth of 445 mm, and overall depth of 510 mm and is reinforced with four No.29 tension bars. The concrete modulus of rupture fr = 3.65 MPa. The elastic modulus of the concrete and steel are, respectively, Ec =27,800 MPa and Es= 200,000 MPa. Determine if the beam will show hairline cracks due to a bending moment M = 108 kN-m and compute the relevant stresses. Provide material properties for concrete and reinforcing steel used in your design.
In all Questions use the Working Stress Method and the flowing material 25 MPa and f, = 420 MPa. properties f = If the stress in the top fiber of the concrete is f = 12.5MPa and in the steel is 400 MPa. Ec 25000 MPa, Es 200000 MPa. Determine the following: 1-Maximum strain in concrete 2- Maximum strain in steel and 3- Flexural strength of the section (the moment M) P 500 mm 300 mm
Assume concrete accepts no tension. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1.25ton.m A = 10cm? E, = 2*10 kg /cm? E. = 2*10°kg /cm f' =150kg / cm? F, = 4000kg / cm? 20 cm 25 cm 20 cm
NO 1 Please solve and answer correctly, give the complete solutions.
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.