3-55: A ring of SAE 301 stainless steel is to be placed on a shaft having a temperature of 20 Celsius and a diameter of 55.200 mm. The inside diameter of the ringis 55.100 mm.  To what temperature must the ring be heated to make it 55.300 mm in diameter and this allow it to be slipped onto the shaft?

Q: *3-44. Determine the magnitudes of F₁, F2, and F3 for equilibrium of the particle.

A:

Q: 37. What factor of safety is needed for a 1.998 in diameter shaft with an ultimate * strength of…

A:

Q: A 2.25 kN m torque is applied to the solid cylinder made up of a hollow cylinder and an inner core…

A:

Q: - 750 mm G. D 225 mm F 900 mm E 1200 mm-

A: Find the reactions at each joint and force in rope.

Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…

A: Given that, AISI 1040 steelDiameter of shaft, D=30 mm,Torque applied on shaft, T=40 N.mBending load…

Q: Figure 8-4 Full Alternative Text 8-5. The gas storage tank is fabricated by bolting together two…

A: As per Expert Guidelines we are supposed to answer only the first question of the given multiple…

Q: A steel tubing has a 1.5-in outside diameter and a 1.210-in inside diameter. It is made of AISI 1020…

A:

Q: The critical speed of the shaft is 847.5 rad/s.

A: Given datathe diameter of the steel rod d = 24 mm = 0.024 mthe length of the steel rod l = 600 mm =…

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Eigure 4)…

A: σx= -126 MPaτxy= 52 MPaθ= 110∘ Note: σy= 0 MPa

Q: A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the bolt.…

A: Given data: The torque required to break the bolt is T = 105 ft-lb. The length of the wrench is l =…

Q: A 2-in.-diameter round steel rod 10 ft long is subjected toa tensile force of 60 kips. How much will…

A: Given Data⇒Diameter of round steeld=2 inLength of round steelL=10 ft=120 inTensile ForceF=60…

Q: Learning Goal: As shown, two composite columns of steel and concrete are used to support a rigid…

A:

Q: 3. Find the proper thickness of 900 mm cast-iron pipe under a 95m head of water with a working…

A:

Q: The axial assembly consists of a solid 1.03-in.-diameter aluminum alloy [E = 9700 ksi, v = 0.24, a =…

A:

Q: Axial loads are applied with rigid bearing plates to the cylindrical pipes shown. The diameter of…

A: To find axial stress in rod 2 and normal strain in rod 2

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

A:

Q: 1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to…

A: Given:

Q: A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod…

A:

Q: The brake piston consists of a full circular part. Its cross section is shown in (Figure 1). Suppose…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.