37. What factor of safety is needed for a 1.998 in diameter shaft with an ultimate * strength of 60,000 psi to transmit 40,000 in-lb torque. A. 2.35 B. 1.95 C. 2.14 OD. 1.55

Q: plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll…

A:

Q: Draw the FRONT VIEW, TOP VIEW , SIDE VIEW of the figure below • Draw the SURFACE DEVELOPMENT of the…

A:

Q: Produce a 3D solid model of the Guard casing and test boss

A: Given Test boss Guard casing To find 3D solid model

Q: Grips appear: a. At key points on drawing objects b. On a separate layer c. Every time you click on…

A: When an object is preselected, the object gets highlighted and little squares will show up on them…

Q: DIMENSION THE OBJECT SHOWN BELOW. NOTE THAT NOT ALL ORTHOGRAPHIC VIEWS WILL REQUIRE DIMEN- SIONS. DO…

A: Orthographic views of a part i.e., Top view and Side/Front view is given here. Grid spacing is…

Q: Based on the front view and the right side profile view shown, use any projection method to find the…

A: Given Front and right view of the object To find Top and isometric view

Q: For the objects shown in isometric below, sketch the top, front, and right side views in the space…

A: Given: Draw front, top view and right side view of the given isometric view.

Q: Shown in the image is a vertical section of a 66 block grid of a gold mine deposit. Each block is…

A: Based on the image presented, which includes varying ore grades ranging from 1.4 g/t to 2.9 g/t in…

Q: The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its…

A: Given: Let us consider the resultant of this force system is the couple-vector CR=-1100i+1500j…

Q: Point "P", as shown below, is located between nodes 2 and 3 of a quadratic 1D bar element. Workout…

A: Given data: location of node 1, x1 = 10.8 mm location of node 2, x3 = 34.6 mm location of point P in…

Q: Instruction: Determine the moment of the force about point A.

A: Given Structure in loading To find Moment about A

Q: For the given multiview projection, draw the corresponding isometric drawing. ME DA

A: For the given multi view projection, draw the corresponding isometric drawing.

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: 3. On the drawing and produced part below, label the following terms: Datum feature symbol Datum…

A: Label the given terms.

Q: Statically Equivalent Loads. A highly idealized biomechanical model of the human body is shown…

A: Given that, FR=150 N,FO=150 N,FL=230 N,FE=320 N, (a) Calculate the moment about the x-axis,…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.