321. A compound shaft consisting of an aluminum segment and * steel segment is acted upon by two torques as shown in Fig. P-321. Determine the maximum permissible value of T subject to the following cooditions: 7, < 100 MPa, T < 70 MPa, and the angle of rotation of the free end limited to 12°. Use G, 83 GPa and G, = 28 GPa. %3D 75 mm dia. 50 mm dia.

321. A compound shaft consisting of an aluminum segment and * steel segment is acted upon by two torques as shown in Fig. P-321. Determine the maximum permissible value of T subject to the following cooditions: 7, < 100 MPa, T < 70 MPa, and the angle of rotation of the free end limited to 12°. Use G, 83 GPa and G, = 28 GPa. %3D 75 mm dia. 50 mm dia.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
Question (1): A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown in the figure. The torques have magnitudes 12.5 kips. in., 9.8 kips, in., and 9.2 kips. in. The length of each segment is 25 in. and the diameters of the segments are 3.5 in., 2.75 in., and 2.5 in. The material is steel with shear modulus of elasticity G = 11.6 x 103 ksi.(a) Calculate the maximum shear stress Tmax in the shaft. (b) Calculate the angle of twist (pp (in degrees) at end D. 13.5 in. 12.5 k-in. -25 in.- B 9,8 k-in. 12.75 in. -25 in.- 9.2 k-in. 12.5 in. c t -25 in.-
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 3730 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.5-m length of shaft. 0.0807 rad 0.1091 rad 0.0556 rad 0.0861 rad 0.1009 rad
A horizontal nickel steel shaft shown in the below Figure rests on two bearings, A at the left and B at the right end and carries two gears C and D located at distances of 250 mm and 400 mm respectively from the centre line of the left and right bearings. The diameter of the gear C is 600 mm and that of gear D is 200 mm. The distance between the centre line of the bearings is 2400 mm. The shaft transmits 20 kW power at 120 r.p.m. The power is delivered to the shaft at gear C and is taken out at gear D in such a manner that the tooth force Fic of the gear C and FID of the gear D act vertically downwards. The gear C and D weighs 950 N and 350 N respectively. The combined shock and fatigue factors for bending and torsion may be taken as 1.5 and 1.2 respectively. (iii) Determine the maximum moment acting on the shaft
A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and B/C = −0.233 rad, calculate the absolute twist of the shaft at point C(oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N.m 280 N.m B 40 N-m D
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3˚ in a6-m length when subjected to a torque of 15 KN-m? What maximum shearing stress isdeveloped? Use G=85 GPa.
What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3° in a 7-m length when subjected to a torque of 10 kNm? What maximum shearing stress is developed? G = 75 GPa
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.
Consider the case of shafts subjected to combined twisting moment and bending moment. A solid circular shaft is subjected to a bending moment of 2800 Nm and a torque of 10,000 Nm. The shaft is made of 45 C 8 steel having ultimate tensile stress of 700 MPa and ultimate shear stress of 500 MPa. Assuming a factor of safety as 5, determine, the diameter of the solid circular shaft. if a hollow circular shaft is to be used in place of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameter is 0.5.