An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R1 = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1 777

An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R1 = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1 777

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two solid circular shafts (i.e., AB and BC) are fixed to rigid walls at point A and C, respectively. Members AB and BC are coupled together through a rigid plate at B. As shown in the figure, an external torque is applied at point B. Determine the absolute maximum shear stress developed in the whole structure AC. Both members AB and BC are made of the aluminum alloy with shear modulus G = 60 GPa. 150 mm 100 mm B 10 mm 5 kN-m Note: ignore the effect of stress concentration. 20 mm
A 28mm diameter steel shaft AB is built into a rigid wall at A and supported by a smooth bearing at B. The lever BC is welded to the end of the shaft. Load P 360 newton is applied as shown in the figure below. Determine the maximum shear stress and the angle of twist if the distance from A to B is 3 meters and the distance from B to C is .3 meters
T.L Tr4 %3D J = " (r* – rf) (Tubular shaft) Tr (Solid shaft) G.J 3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to 50 diameter steel segment. The ends of the shaft are attached to rigid supports (fixed supports). Calculate the absolute maximum shear stress developed in each segment when the torque T= 5.1 kN-m is applied (a = 2 m and b = 1.5 m). Use G = 35 GPa for bronze, and G = 75 GPa for steel. (21 pts) 75 mm 50 mm Bronze Steel
A shaft fixed to a wall at B is made of an outer steel tube of 1" outer radius (G = 11,400 ksi) bonded to an inner solid brass core (G = 5200 ksi) of 0.5" radius. For the torque applied at A determine the maximum shear stress in each material and the rotation of A. Note: Each material carries part of the total applied torque. Treat end A %3D as a joint. Ans: 1977 psi steel, 451 psi brass 4 ft 0.5 in. 1 in. T= 250 lb-ft (a) all cunnorted at A and B. For
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.
The circular cross-section, L=0.5m long console BC shaft in the figure is forced to twist with P1=2 kN, P2=8 kN due to the forces on the belts connected to the pulley C. The radius of the pulley is R=0.4m and its weight is W=3 kN. Calculate shaft diameter D based on the assumption of maximum shear stress (TRESCA). Yield strength of the shaft = 240MPa and safety factor is S=2 1 kasnak D 2R P2 |B kayış y
H K T A solid shaft is subjected to forces and a torque as shown in figure. The diameter of the shaft is 35 mm, T=75 N.m., V=3 kN, P=4,7 kN and L=117 mm. Determine the shear stress (T) at point H (MPa). Note: If the stress has negative direction, use sign. Yanıt:
An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure The length I of the member is 3 m. MT R Ri If a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. 777
A torque of Tx=200Nm and a torque of Mz=260Nm are applied to the stepped shaft in the figure. Calculate the maximum stresses that will occur in the bar section, taking into account the stress concentration.
The hollow cylinder shaft shown in the figure has an inside diameter of 15mm and the gears are subjected to the indicated load. The bearings at points A and B only exert forces on the shaft in the y and z directions. If the allowable shear stress is known to be operm = 70 MPa. Use the maximum shear stress theory of failure and proceed to:a) Draw the bending moment diagrams My and Mz and torque T, determine the magnitude and location of the absolute Maximum Moment.b) Determine the outer diameter of the shaft to within 1 mm.