Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at 4, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m 2 m 100 mm 50 mm T= 50 kN. m

Question 4. The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at 4, and a torque of T 50 kN.m is applied to it at C, determine the angle of twist that occurs at C and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst 115 GPa, Gbr 56 GPa. 3 m 2 m 100 mm 50 mm T= 50 kN. m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4.) A 12 watts DC motor is used to run a remote-controlled car. A 3-inch aluminum shaft, with a diameter of 1/8 in., is connected to the motor rotates 5000 RPM. Determine the maximum shear stress on the shaft and the angle of twist if the shaft will be supported at the free end. Use G = 28 GPa
What must be the maximum torque of a 5mm diameter aluminum wire so that it can be twisted through 1 complete revolution without exceeding a shear of 42N/mm². Take, G-27 GPa.
The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm. If the shear stress in the shaft is not exceed 120 MPa and the angle of twist is not exceed 5; find the largest allowable of P. For steel; use G = 80 GPa.
In the image below, B and C are pulleys. The belts on the pulleys exert the forces shown in the diagram below, generating a torques at each pulley. If pulley B has a radius of 150 mm and pulley C has a radius of 100 mm, determine the maximum shear stress (in MPa) in the shaft if it has a 40-mm diameter.
5.2 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
A solid shaft is subjected to a twisting moment of 150 kNm. If the angle of twist is 8º per meter of the shaft and the shear stress is not to exceed 550 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G 250 GPa. Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in mm The sutable Diameter of the shaft is in mm The maximum shear strain is
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
Please I need help. This problem involves torsional strain. Thank you.
2
2. Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque ofT 171N.m the missing Torque 171(T).