188 NOTES: ALL FILS & RNDS R.10 PART SYM ABOUT C ALL FIN. SURFACES 25/ (B 2.160 2X 0.188DR Ø.8125-.8130 RM 2 HOLES IN LINE Zø.625DRL 01.000 V.25 2X ø.281DR |SFØ.625 (F) .720– .360 R3.00 TI-84 Plus CE Ø1.36 Ø1.40 .10 1.940 .50- M) .860 6Q .72 .300 -1.08 (N) 4.04 2.32 THIRD ANGLE PROJECTION t f1 tblsei f2 format f3 calc f4 table f5 MATERIAL UNSPECIFIED TOLERANCESI MALLEABLE IRON window CHKD SCALE 1:2 ZOom REDRAWN BY R.SCHOFIELD MŽ trace 2-PL DEC (X.XX)±.02 DWN BY graph W.E.HASEK DWG NO. quit ins 3-PL DEC (X.XXX>±.005 TITLE 21A035 mode del +,010 -.002 DOVETAIL BRKT DRILLED HOLES link list ANGLE ±0° 30' X,T,0,n stat angle B draw C distr th apps prgm

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: . a. On the part shown, show a angularity specification to orient the angled surface in relation to…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Did the person…

A: Yes, the given print is created by using the cylinder rule. Hence, the option (a) is correct.

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: C 80±0.5 - 40 50±0.5 20 la be oxi odr wode wo B A.

A:

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: Find the number of rotations of wheel 3 in rotations per minute (rpm) wile the load A is moving down…

A:

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance…

A: Perpendicularity: In GD&T the Perpendicularity is defined the two different…

Q: igh precision in angular measurements can be made using a sine bar. For using a 200 mm sine bar to…

A: Given:Length of sine bar, L=200 mmangle=49o 20'angle=49+2060=49.33oDiameter of rolls, d=35 mm

Q: GER SCALE 9 v 1.3- A 3"-2 ACME .75 1.5 "5 SECTION A-A Ø3.75- D-50 Top and front views of the…

A: Adjusting screw is a screw with threads from 40 to 100 threads per inch. Typically stainless steel…

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of…

A: Introduction: Engineering drawings are a subset of technical drawings. The goal is to provide all of…

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: Assuming there is no wheel slippage, what is the wheel rotation speed in revolutions per minute of a…

A: Given data: The time for car is t=5 min=300 sec The covered distance is s=181 m The diameter of the…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: Define the term nominal dimensions?

A: In manufacturing, a nominal size or trade size is a size "in name only" used for identification.

Q: How do you find the distance if the dimension is 1 5/8 and scale is 3/4= 1 ?

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.