#5. On the part below, calculate the allowable min and max hole sizes as well as the size of the MMB position boundary created. Please refer to attached image. A,LG-80±0.5C.4050±0.5 .20B.5. On the part below, calculate the allowable min and max hole sizes as well as the size of theMMB position boundary created.SizeМaxMinМaxMinSizeMMBMMB13.28

Answered: Image /qna-images/answer/3046fef8-a635-438e-ab90-9a06618ca972.jpg

Answered: C 80±0.5 - 40 50±0.5 20 la be oxi odr…

Engineering

Mechanical Engineering

C 80±0.5 - 40 50±0.5 20 la be oxi odr wode wo B A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sketch the top, front and right side views of the isometric. Scale the orthographic views so that one grid unit on the isometric is one grid unit on the rectilinear grid.
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. 4. Establish all necessary dimensions as basic. 5. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 6. Position the three holes within a diamter of .012 at MMC relative…
Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish the right face in the side view as datum feature A. Qualify this feature with a flatness of .005. 2. Establish the top surface in the front view as datum feature B. Qualify this feature with a perpendicularity of .005 to datum feature A. 3. Establish the left surface in the front view as datum feature C. Qualify this feature with a perpendicularity of .005 to datum features A and B. Please refer to the attached image.
7. Give all the location dimensions between the datum target area, A1 ,and datum target point, A3 . X = _________________, Y = ________________, Z = __________________
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
Figure out the 2D sketch of housing using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve (red) 37 30 14 R 2 holes 72 Dia 12R 60R 30 R 24 10 R 15R Housing 60 R
Calculate the Total Reading from the figure given below for Least count 0.02mm Vernier caliper Image 1 2 3 4 5 'o 1 2 '3 5 '6 7 '8 9 For more clarity of Vernier scale refer the magnified image given below 5 6 7 8 9 Answer:
None
Sketch the 2D figure using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 20 36 R 20R BR 36 BR 15 45 45 Upright | 2 holes 10 Dia 36K 158
Basics in engineering drawing