10. A spiral easement curve has length of 182 meters with a central curve having a radius of 338 m. Calculate the offset distance to the third quarter point on the curve. d. 6.89 m a. 5.74 m b. 8.90 m c. 6.54 m

10. A spiral easement curve has length of 182 meters with a central curve having a radius of 338 m. Calculate the offset distance to the third quarter point on the curve. d. 6.89 m a. 5.74 m b. 8.90 m c. 6.54 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Two parts are assembled as shown in the figure below. Assume that the dimensions x and y are…

A: Given data,standard deviations

Q: 1.46: A contractor claims that the mean compressive strength for a concrete mix is 5000 psi (μ) and…

A: Given data contractor’s correct or not contractor’s correct or not

Q: What can you conclude?

Q: Following are the results of a sieve analysis. Determine: a. Cu b. Cc c. So Sieve No. 4 6 10 20 40…

A: Sieve analysis is a method used for determining the particle size distribution of a coarse grained…

Q: . What is a particle size analyzer and what is the principle it works upon?

A: A particle size analyzer is is used to determine the size and arrangement of particles that make up…

Q: According to fuller equation, to draw the maximum density line for aggregate gradation shown below ,…

Q: Which of the following expresses Euler's column formula?

A: Euler’s column formula: - This formula is useful to find critical buckling load for long column.

Q: Problem A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves…

A: Size of sieve for which 60% of sand passes, D60=2mmSize of sieve for which 300% of sand passes,…

Q: please help us in this data table please help to fill it up but if possible the most important is…

A: The grain size distribution of the soil sample can be performed by Sieve analysis Dry sieve…

Q: 4. The percentage of fine aggregate 5. The percentage of filler material

A: 4. Fine aggregate range lies from 4.75mm to 0.075mm. Hence from the table: % Fine aggregate = 65-3 =…

Q: Given the data below about the Axial Strain (%) vs Deviator Stress: Axial Strain (%), X Deviator…

A: Axial strain vs deviator stress curve data set is given. Lagrange interpolation is used to get any…

Q: The tensile test of a specimen of rebar conducted by students in the Construction Materials and…

A: Given data: The tensile test of a specimen of rebar conducted by students in the Construction…

Q: Calculation: T = (2Pmax)/(TtLd) Where: T= splitting tensile strength, psi (MPa) Pmax = maximum…

Q: is the total permissible variation in its size. Select one: O a. tolerance O b. dimension O c.…

A: Tolerance is the total permissible variation in the size of a dimension. Tolerance is the difference…

Q: A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that…

A: Given data, Tensile force = 20 kN Gauge length = 50 mm After force gauge length = 50.122 mm…

Q: Q5: A/A tensile test was conducted for a sample and the relationship between stress and strain was…

A: As per the guidelines of Bartleby we are supposed to answer only first three sub-parts of a…

Q: According to fuller equation, to draw the maximum density line for aggregate gradation shown below ,…

A: 63% is passing through the sieve 4. 75 mm Similarly 100 % is passing through 19.5 mm sieve 95% is…

Q: Part 2 (Identification): Identify each part of the stress-strain diagram numbered below. (3)…

A: 1) Proportionality limit 2) yield limit 3) yield plateau 4) ultimate point ( ultimate stress or…

Q: Test Data and result Sample # Age (days) R (mm) Area (mm^2) Q(N) о (MPa) 1 7 100 400000 7 100 410000…

A: Compressive strength is defined as the ratio of the compressive force applied per unit surface area…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A: Given data, Size of each grid square = 880 psi

Q: Initial weight: % Passing Weight Retained 1.5 kg 1.634 kg 2.5 kg 1.8 kg 2.273 kg 0.233 kg 0.06 kg…

Q: Thank you for your answer but I can't see the right side of the page, see image below what i see

A: HMA = 210 mm Base = 300 mm Sub-base = 500 mm Reliability = 95% ∆PSI = 1.75 S0 = 0.45 TSI = 2.5 Cd =…

Q: There are several reasons why JMeter has become the de facto standard for performance testing.

A: The open-source availability, user-friendly interface, cross-platform compatibility, scripting…

Q: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

A: In the picture is a distribution graph of the sphericity of a sample of aggregate materials. The…

Q: Propose a way to reduce water hardness

Q: Is the relationship between BOD and OD directly proportional ?

Q: minimum in a direction a) parallel to the grains b) perpendicular to the grains C) along an axis…

A: Compressive strength is maximum along the grain of timber whereas Compressive strength is minimum…

Q: 30 mm 15 mm 70 mm 30 mm 55 mm B" /B 110 mm 100 mm DA 70 mm 30 mml The block is deformed into the…

Q: A. A materials engineer conduct a Moisture Content Test. Here is the result Oven dry Sample (2DD +…

Q: There are three basic types of testing, and the order in which they are carried out is outlined.

A: What is testing? Testing is the practice of making objective judgments regarding the extent to which…

Q: Which length shall I use to calculate current density: the whole bar length or the embedded length…

A: Answer embedded length is known as the length of the embedded steel reinforcement, The embedded…

Q: A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given data- A bar specimen- Diameter d=36 mm, Change in diameter ∆d=0.0046 mm, Gauge length L=200…

Q: Calculate the tensile strength in the Brazilian examination

Q: estimate the value of Froude's number. a) 065

A: To find : Froude's number

Q: 1. Given the results of an Atterberg limit test. Complete the test report which will include filling…

Q: a ga in tension with the following results: Applied 1 Strain Force (N) (mm) (%) 0 5.000 Stress (MPa)…

A: We…

Question

10 please give the correct ans and the solution

10. A spiral easement curve has length of 182 meters with a central curve having a radius of 338 m.
Calculate the offset distance to the third quarter point on the curve.
d. 6.89 m
a. 5.74 m
b. 8.90 m
c. 6.54 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Mechanical Properties W/ complete solution
W o No. Load Elongation Lo P(KN) SL(mm) |(mm) Area O eng (KN/m²) Еeng (mm) m² 1 100 36.1 2 38 0.02 100 36.1 3 76.2 0.12 100 36.1 4 92.7 0.25 100 36.1 107 0.50 100 36.1 6. 149 2.03 100 36.1 7 160.6 3.55 100 36.1 8 102 3.87 100 36.1 9 100.7 4.01 100 36.1 10 98.33 4.12 100 36.1 11 155 4.65 100 36.1 12 142 5.1 100 36.1 13 124.2 5.84 100 36.1
Discuss the advantages and disadvantages of different methods in determining particle size?
If the specimen is originally square and has dimensions of a = 4 in., b = 3 in., and a thickness of t = 0.4 in., determine its new dimension a' after the load is applied. Express your answer to six significant figures and include appropriate units. a' = 4.00737 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 5 attempts remaining 0 in Determine its new dimension b' after the load is applied. Express your answer to six significant figures and include appropriate units. μᾶ b= 3.00333 ? in Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
C and D please
What are the steps followed in testing?
Explain LAP SPLICING. Illustrate a sample figure about it.
Procedure:1. Measure the dimension of the cylinder. Determine the diameter of the specimen to the nearest 0.01 in (0.25 mm) by averaging three diameters measured near the ends and the middle of the specimen and lying in the plane containing the lines marked on the two ends.2. Determine the length of the specimen to the nearest 0.1 inch (2.5 mm) by averaging at least two length measurements taken in the plane containing the lines marked on the two ends.3. Center one of the plywood strips along the center of the lower bearing block of the testing machine. Place the cylinder on the plywood strip and align so that the lines marked on the ends of the specimen are vertical and centered over the plywood strip.4. Place the second plywood strip lengthwise on the cylinder and place a 2ˮ x 2ˮ x 14 steel bar over the plywood strip.5. Lower the upper loading head until the assembly is secured in the machine.6. Apply the compressive load slowly and continuously until failure. The rate at which the…
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…
Question 4 Comment the four types of sieve analysis diagrams, which appear in the figure below: Continuum, Uniform, Gaps, Open. % Passing 100 O Continuum A Gaps Sieve size Open Uniform