0, 339 mm 124, 340 mm 154, 628 mm 64, 220 mm 40 kN/m 20, 150 mm 1.5 m If the allowable bearing stress for the material under the supports at A and B is 1.3 MPa, determine the size of square bearing plates A' and B' required to support the load. Dimensions of the plates to the nearest mm. The reactions at the supports are vertical. Take P=110 kN. A' 3 m B 1.5 m-

0, 339 mm 124, 340 mm 154, 628 mm 64, 220 mm 40 kN/m 20, 150 mm 1.5 m If the allowable bearing stress for the material under the supports at A and B is 1.3 MPa, determine the size of square bearing plates A' and B' required to support the load. Dimensions of the plates to the nearest mm. The reactions at the supports are vertical. Take P=110 kN. A' 3 m B 1.5 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to the figure shown below, the hinged support at A is in double-shear connection while the support at B in single shear shear connection. Forces P is applied at C and F is an axial force produced from a member BD connected at B. Given data: x = 1.2 m, y = 1.5 m and z = 1.8 m. ∅ = 20 degrees. If the axial stress of BD is limited to 180 MPa, wherein BD is made of 50-mm square tubing with thickness is one-tenth of its dimension, which of the ff. most nearly gives the shearing stress of the 20- mm dia. pin at A in MPa.
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
The block slides down an incline. It starts from rest and, after moving 6 ft, strikes a spring (k= 100 lb/in). Determine the maximum deformation of the spring. Coeff fr= 0.20. 600 lb 6' WW 3 4
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi, determine the maximum load P that may be supported by the structure. (1) 6 ft 4ft O 15.75 kips 18.32 kips O 9.55 kips O 14.24 kips O 19.92 kips
Write the solutions legibly.
Q1. A horizontal bar of nagligible weight and assumed rigid is supportad by two rads, AB and CD, and hingad : the right and. Data for the rods are as follows: Rod AB: L= 2 m, A= 1950 mm. E= 80 GPa ; Rod CD: L=2.5 m, A= 1200 mm, E= 200 GPa Ifthe maximum unit stress in AB is not to exceed 90 MPa, and the maximum allowabla load for CDis 110 kN, determine the maximum value of the force F. B F 0.60 m. 1.90 m 1.20 m
Q1/ Draw the normal stress distribution over the cross section on which the maximum normal stress occurs. El = 80000 MPa., E2=20000 MPa A 10 kN/m M- 20 kN MATERIAL 10 MM B MATERIAL MATERIAL 2 100 MM MATERIAL 2 -2 M- -40 mm Q2/ the beam in Q1 (a) find the spacing required between Nails 1 (b) find the spacing required between Nails 2, shear force per nails is 70 kN. 50 mm 16 mm Nail 1- 10 MM- 140 mm Nail 2 16 mm
A 29-mm-diameter solid steel shaft supports loads PA = 1100 N and Pc = 2810 N, as shown. Assume L₁ = 105 mm, L₂ = 176 mm, and L3 = 210 mm. The bearing at B can idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of the maximum bending stress in the shaft. Answers: max = 1₂ Po MPa, x = mm.