A 29-mm-diameter solid steel shaft supports loads PA = 1100 N and Pc = 2810 N, as shown. Assume L₁ = 105 mm, L₂ = 176 mm, and L3 = 210 mm. The bearing at B car idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of th maximum bending stress in the shaft. Answers: 1₂ Pc

A 29-mm-diameter solid steel shaft supports loads PA = 1100 N and Pc = 2810 N, as shown. Assume L₁ = 105 mm, L₂ = 176 mm, and L3 = 210 mm. The bearing at B car idealized as a roller support and the bearing at D can be idealized as a pin support. Determine the magnitude omax and location x (measured positive to the left from D) of th maximum bending stress in the shaft. Answers: 1₂ Pc

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 8800 psi, and the vertical deflection of joint D is not to exceed 0.400 in. when a load of P = 3000 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 70 in., b = 24 in., and c = 24 in. a b Answer: d= D P B in. C
#2 handwritten then box the final answers
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.