0, 339 mm 124, 340 mm 154, 628 mm of the allowable bearing stress for the material under the supports at A and B is 1.3 MPa, determine the size of square bearing plates A' and B' required to oad. Dimensions of the plates to the nearest mm. The reactions at the supports are vertical. Take P=110 kN. 64, 220 mm 40 kN/m 20, 150 mm -1.5 m- 3m 1.5 m-

0, 339 mm 124, 340 mm 154, 628 mm of the allowable bearing stress for the material under the supports at A and B is 1.3 MPa, determine the size of square bearing plates A' and B' required to oad. Dimensions of the plates to the nearest mm. The reactions at the supports are vertical. Take P=110 kN. 64, 220 mm 40 kN/m 20, 150 mm -1.5 m- 3m 1.5 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Required information Consider the beam and loading shown. If a=8 in, b=9.0 in, c=1 in. For a section at n-n, determine the shear stress at b. A 25 kips 20 in.- 10 in. 25 kips - 20 in.- B a +6 i in.. in. b b a с in.
SOLVE FOR A,B,C
y3D3 W = 15 kN/m 个个 L%3D24M Determine the tension (KN) at midspan.
Determine the principal stress in the beam at point A. 60 kN 50 mm 150 KN 150 mm mm -05m- -025m
The bell crank shown is in equilibrium. (a) Determine the required diameter of the connecting rod AB if its axial stress is limited to 120 MPa. (b) Determine the shearing stress in the pin D if its diameter is 20 mm. B 30° 260 mm- 180 mm A 3. C D 140°. DOUBLE 28 KN SHEAR
The block slides down an incline. It starts from rest and, after moving 6 ft, strikes a spring (k= 100 lb/in). Determine the maximum deformation of the spring. Coeff fr= 0.20. 600 lb 6' WW 3 4
Bar (1) has a cross-sectional area of 0.75 in.?. If the stress in bar (1) must be limited to 35 ksi, determine the maximum load P that may be supported by the structure. (1) 6 ft 4ft O 15.75 kips 18.32 kips O 9.55 kips O 14.24 kips O 19.92 kips
Q1. The solid shaft has a radius of 4 cm a. Find the state of stress at H. b. Draw the Mohr's circle for the state of stress at H. c. Find the principal stresses and orientation of principal planes, and the maximum shear stress and its orientation at H. P PL B= 8= AE V 2,₂ = 2/- (0₂+0₂) 2y = 7/7 - (0₂+0₂) Ex 6cm 8= 100 N Pdx √" (= AE V 4-7-7 (9₂ +9₂) == EE To AL 729 12 cm 10 cm My 50 N E uz 100 N 8cm 8cm 100 N 시구
Design a channel section (shape purlin placed on a sloping roof trus8 with dead load of 0.15 kN/m (cladding and insulation), a live load of 2 kN/m and wind load of 0.5 kN/m (suction). The purlins are spaced 2 m cle and of span 4 m, simply supported on a rafter at a slope of 20.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
Q1/ Draw the normal stress distribution over the cross section on which the maximum normal stress occurs. El = 80000 MPa., E2=20000 MPa A 10 kN/m M- 20 kN MATERIAL 10 MM B MATERIAL MATERIAL 2 100 MM MATERIAL 2 -2 M- -40 mm Q2/ the beam in Q1 (a) find the spacing required between Nails 1 (b) find the spacing required between Nails 2, shear force per nails is 70 kN. 50 mm 16 mm Nail 1- 10 MM- 140 mm Nail 2 16 mm
3. A planar truss is constructed of steel members, all of which have a cross-sectional area of 3000 mm?. Determine the nodal displacements, reactions and element stresses. G 2 m B D 2m 50 kN 460 kN