DAD 220 Module 5-2 Analysis and Summary Golda Smith

Please answer the 4th question

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

LESSON: AUTODESK AUTOCAD Choose from the choices:

Subject: Air Pollution Formation and Control Do not just copy and paster other online answers

A dust particle is suspended in the air (floating due to a small updraft and its own low mass) when a powerful loudspeaker plays a very low note (2 Hz so it can’t be heard but you can actually see the speaker move!). How will the dust particle move as a result of the speaker 
being turned on? Question 3 options:   A)  The dust particle will move up and down.   B)  The dust particle will be pushed across the room.   C)  The dust particle will move in a circular path.   D)  The dust particle will move side to side.

Handwritten solution required. Strictly don't use chatgpt. If you use chatgpt ,I will report the answer for sure. Mechanical engineering dynamics.

A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues.  You must follow the following steps to help the team:  STEP 1  Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following:  The input and output heat and net output work The expansion and compression strokes The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work. STEP 2  Explain the mechanical…

AMNT 280 Assignments 1-4 Media Presentation Categories Of Reciprocating Engines   Develop a Media Presentation develop a power point media presentation Presentation will require researching a module specific topic For this activity you will research the four categories of reciprocating engines In your presentation address the following: 1 Research the four different types of reciprocating engines2 Provide an overview of the design, construction, and firing order of each engine 3 Provide research concerning which air frame used the engine Presentation Guidelines Note:This information applies to all Media Presentation activities and will not be repeated Present your research material in the format of a written document (Introduction, body, and conclusion) Presentation requirements consist of 5-7 slides with a balance of both bullet text information and images; does not include the title or reference slide APA formatting and structural guidelines apply  Additional information…

i need correct explanation my best wishes ton

I need help solving this problem.

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

This is Mechanical Engineering. Please answer with clear work and answers. Thank you

TRUE OR FALSE Directions: Choose true is the statement is correct, otherwise choose false. 1. Literature is not related to a certain region’s culture, tradition, history and people. 2. All written, oral, and multimedia forms of work are considered literature. 3. Poetry commonly utilizes rhymes and figures of speech while prose uses formal sentence structures. 4. Drama is delivered on a theatrical stage with actors and actresses. 5. Fictional works have the same elements of non-fictional works. 6. Facts, information, and statistics are focused on non-fictional works. 7. Human history and advancements were possible without the role literature. 8. The standard of universality conveys that literature must be perpetual and timely. It is forever relevant and it appeals to one and all, anytime, and anywhere. 9. Intellectual beauty expresses that a literary piece must stimulate thought about life and human nature, while suggestiveness pertains to how it evokes emotion of the reader. 10. All…

Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…

Match correctly and give one line explanation to all of your matching.