Unit 8 Discussion- Reflection

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

I was given a practice question for transforming equation. In the image I will have a slide the lecture note of an example of it being done but I do not understand what was done exactly. Please explain how to answer the question. Thank you

please put into DMS format with final solution. Thank you

Please solve the following by hand and without the use of AI. Thank you!

I need help with simulink. It is my first time using simulink. I am trying to make a simulink program turning on the LED on the board for 10sec for an Arduino Mega 2560. I have attached an image of what I tried to do. After I run, it just says no diagnostic. How do I know if I did this correctly or not?

Given the trasnfer function G(s) numerator and denominator coefficients for Matlab code should be: O s³+2s+1 2s4+2s²+1' the num= [1 0 2 1] and den=[2 020 1] O num=[1 2 1] and den=[2 0 2 1 1] O num=[1 2 1] and den=[2 2 1] O num=[1 0 2 1] and den=[2 2 0 1]

21. The programmer uses three-point method for UT[2] setup for a sharp-tip pointer. If the programmer recorded each of three-points by precisely contacting the sharp-tip to the tip of the stationary reference pointer on the table, then (a) UT[2] setup is accurate (b) UT[2] setup is not accurate (c) the accuracy of UT[2] setup is still uncertain 22. User frame UF[3] is accurately set up on the part reference surface which is unparallel to the surface where the robot is mounted. To jog the robot TCP to move perpendicularly to the part reference surface, the programmer (a) needs to select World jogging coordinate system (b) needs to activate UF[3] and select User Frame jogging coordinate system

I need help coding in MATLAB. I have a .txt file containing the following data. That data is saved in a file named data.txt. I am wondering how I could extract all or some of that data into another .m file. Can you show me the code.   [[5.0018696581196584, 17.863820207570207, -13.086858974358975], [5.0018696581196584, 17.863820207570207, -13.086858974358975], [5.0018696581196584, 17.863820207570207, -13.086858974358975]]

DISCUSS THE STEP-BY-STEP PROCESS OF HOW TO COME UP WITH A SOLUTION.   *Preferably if you typed the answer Thumbs up guaranteed If you discuss the steps. Thankyou!

(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions                        One feedforward solution

I have attemped to start the question by first using the equation: log_{10}W_{TO} = A+Blog_{10}(CW_{TO} - D) After working out some stuff I got to: log_{10}W_{TO} = 0.833+1.0383log_{10}(CW_{TO} - 53000) Using the info give, C = M_ff I tried calculating the M_ff but needed the weight ratios for both cruises, loiter, and flight to another airport. I used the range and endurance equations for loiter and flight to another airport but cannot do cruise as I do not have the Mach number. I don't know how to continue.

Please examine how you got answer step by step please