Tumanda_Assignment #1

I was going over the equations for the notes in class and I had a thought. Based on the equations in the image, you could get negative propellant mass. So, I coded it in matlab and I got negative mass. How is that possible? I think I used practical values for the velocity and mass ratio and so on. Did I do something wrong?

E O ".ll Asiacell :D docs.google.com/forms Q1: Complete the pairs of sentences with the verb in brackets. Use the present simple for one and the .present continuous for the other إجابتك |-- (think) -1 of your problem. I (think) there's good solution إجابتك - (see) -2 you- What I mean? What time- you * ?(see) the film إجابتك

I need the answer as soon as possible

Answer correctly only. I

⦁ “God himself could not sink this ship” This is an advertisement for the Titanic, produced in the early 1900s. However, after colliding with an iceberg at dawn on April 15, 1912, two rivers were formed, and out of the 2,200 people on board, 1,500 people, including the captain, sank with the ship. According to a later investigation, the “temperature change theory” (DBTT theory) was the most promising cause of the sinking. Give a brief guess of the cause of the ship's sinking in relation to temperature.

help please!!

Please answer question and just send me the paper solutions asap dont type the answer question 2abc asap

Build the pneumatic circuit in the following pneumatic sequence using the cascade method: [A- B-] [C+ D- A+] [C- B+ D+]

Build the pneumatic circuit in the following pneumatic sequence using the cascade method: [A+ B+] [A- B- C+ A+] [B+ A- B- C-]

Chrome File Edit View History Bookmarks People Tab Window Help McGraw-Hill Campus - ALEKS Science - CHM1045 GEN CHEM 1 BLENDED 669113 A bconline.broward.edu/d21/le/content/466883/fullscreen/12868783/View McGraw-Hill Campus - ALEKS Science O GASES Interconverting pressure and force A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 470.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 2.80 MN. pressure vessel bolts side View port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. O cm Explanation Check O2021 McGraw-Hill Education. All Rights Reserved. Terms of Use FEB

Solve only D E AND F PARTS HANDWRITING PLEASE

SOLVE OTTO CYCLE PROBLEM IN EXCEL

I need help solving this problem.

Engine Cycle: Our inventor is still trying to design a heat engine that will outperform the Carnot cycle .. Design #801-456 is for an ideal, reversible engine that operates with the cycle shown below (A → B → C → D → A). The engine contains 0.421mol of a gas that has a heat capacity ratio of y = 1.300. Point Pressure [N/m²] Volume [m³] Temperature [K] A 1.05 x 105 0.010 300 B 1.85 x 105 0.010 529 1.85 x 105 0.014 751 D 1.05 x 105 0.014 426 PA B A D V (a) What is the efficiency of this engine cycle? (b) What is the efficiency for a Carnot cycle working between the same maximum and minimum temperatures?

sample calculations 目 File Edit View Insert Format Data To 100% $ % .0 .00 12: fx | A 1 Variable Value Units diameter height m 4 volume m^3 3 The image above shows a section of a Google sheet. What formula should be written in cell B4 to calculate the volume of a cylinder with a diameter value in B2 and height in B3? a) =0.25*PI()*B2^2 * B3 b) =PI()*B2^2 * B3 c) =pi*diameter^2 * height d) =PI*B2^2 * B3 3 5

Please solve i requested to u solve Handwriting. D E And F parts Thanks

13. User tool frame UT[3] was set up by the programmer with three-point method for UT setup provided by FANỤC robot system. Which of the following statements is correct. (a) UT[3] frame is measured relative to UF[h] frame. (b) The orientation of UT[3] frame is the same as the orientation of default TCP frame (i.e. Def- TCP frame). (c) The origin of UT[3] frame is exactly aligned to the origin of default Def-TCP frame. 14. Using three-point method for user tool frame UT[k] setup, a robot programmer can set up the user- defined of UT[k] for an end-effector. (a) position (i.e. origin) (b) orientation (c) position (i.e. origin) and orientation