Advanced Aircraft System

Investigate, and select appropriate sensors for the specified system.

Subject: Mechanical Measurements Do not copy other online answers

(Can someone help me with this just need a P&ID solution meeting the requirements and explanation. thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 1:Cold liquid continuously flow in a tank where its temperature is maintained at 90° C.Steam passes through the tubing which supplies energy for heating. Requirements: One feedback solution                        One feedforward solution PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions                        One feedforward solution PROCESS 3: Product is charged in a closed, jacketed reactor where it is stirred. The reactortemperature is controlled through the uninterrupted flow of coolant in the…

Fundamental of mechatronics technology

A. A customer asked you to explain your choice of a temperature sensor that you used for his PCB. Initially, there were two sensor options. To compare between them, you decided to test their accuracy and precision. Accuracy of a sensor is a measure of how near its reading is to the real value, the nearer the measured value to the real value the better. While precision is a measure of how widely spread the readings of a sensor are [relative to each other] when measuring the same variable, the narrower the spread the better. So, you tested the two sensors by measuring the same temperature, which was 100 C of boiling water, and you recorder the following 10 measurements of each sensor. Which Sensor has higher accuracy, and which one has higher precision. Sensor Sensor readings when measuring 100 C 99.65 100.05 103 102 99.3 s1 100.1 99.1 100.5 99 98.8 98.78 96.9 101.4 98.88 99 S2 99.12 98.9 99 98.69 99.2

Sensor systems for obstacle detection and avoidance in mobile robots. • Design and develop a suitable processor-based Data Acquisition (DAQ) system and external hardware to interface, measure, display and store the responses from the selected sensors.

System Specification The aim of task 2 is to design a simulated obstacle detection sensor system for a mobile robot platform. You should assume your chosen sensors will be placed on a small mobile robot platform as designed in task 1. The sensor system must be able to detect objects within the range of 0mm to 1000mm and have a field of vision of 90 degrees (see diagram below). You may need to use multiple sensors to achieve the desired specification. Robot platform H 0-1000mm range 90° sensor view Example object

Conventional float actuated device is used as a level measurement sensor, which consist of pulley and a pointer which move over a graduated scale. Let say you are asked to develop a controller-based float actuated system having a sensor for level measurement or may be more than one sensor is required for accurate level measurement, which sensor will you use and why? Draw the whole schematic showing the position of the sensor or sensors. Will pulley be part of your new digital system, if yes justify your answer, if no, then how you will develop a system without using pulley.

Assume that a security model is needed to protect information used in the class you aretaking—say, the information in your course’s learning management system. Use the CNSS model to identify each of the 27 cells needed for complete information protec-tion. Write a brief statement that explains how you would address the components represented in each of the 27 cells.

1.Identify a mechatronics system being used by you in your daily routine. Analyze its elements andstate its importance in the functioning of that system.2. Define sensors and list the various specifications that need to be carefully studied before using aThermocouple for reading the temperature of a furnace.3. Explain the significance of the following information given in the specification of the followingtransducer,Thermocouple Sensitivity: nickel chromium/nickel aluminum thermocouple: 0.039 mV/ºC when thecold junction is at 0 ºC.

Mark the good definition

Read each statement carefully and answer by True or False (if False then, correct the statement). 1- Process control combines how physics, chemistry, and biology work in operating equipment and an understanding of dynamic systems. 2- When a second letter is used in instrumentation symbols, e.g., Pressure Indicator Controller (PIC), it defines the measured or initiating variables. 3- P&ID contains the sensor details such as physical principle and measurement range. 4- FRC 82516: Flow Recording Controller, area no 825, process unit 8, loop number 16. 5- P&ID excludes equipment identification.

Orthographic view of the component using creo software

• Characterize and evaluate the sensor performance use real data already collected or extrapolated information from the sensor datasheets. • Produce a written report documenting: the choice of sensors, sensor evaluation, the developed processor/measurement system, and overall system performance.

Compare the electromagnetic vibration sensor and piezoelectric vibration sensor types in terms of EMI resistance, off-axis sensitivity, mounting orientation, and mechanical durability, and hence make recommendations to improve the operating efficiency of the vibration monitoring unit of the vibration monitoring system of the engine-gen set. You are encouraged to use clearly labeled schematic diagrams to explain the principles of operation of the sensors and why EMI may be significant in the environment and hence a sensor type with better EMI resistance should replace the electromagnetic type sensor

Sensor systems for obstacle detection and avoidance in mobile robots. • Design and develop a suitable processor-based Data Acquisition (DAQ) system and external hardware to interface, measure, display and store the responses from the selected sensors. • Characterize and evaluate the sensor performance use real data already collected or extrapolated information from the sensor datasheets.

: Fundamentals of Mechatronics Technology

The Weather Monitor. Your South American expedition splits into two groups: one that stays at home base, and yours that goes off to set up a sensor that will monitor precipitation, temperature, and sunlight through the upcoming winter. The sensor must link up to a central communications system at base camp that simultaneously uploads the data from numerous sensors to a satellite. In order to set up and calibrate the sensor, you will have to communicate with base camp to give them specific location information. Unfortunately, the group's communication and navigation equipment has dwindled to walkie-talkies and a compass due to a river-raft mishap, which means your group must not exceed the range of the walkie-talkies (3.0 miles). However, you do have a laser rangefinder to help you measure distances as you navigate with the compass. After a few hours of hiking, you find the perfect plateau on which to mount the sensor. You have carefully mapped your path from base camp around lakes and…

Berserk - Chapter 2- Read Berserk compressor. reggienet.illinoisstate.edu https://reggienet.illinoisstate.edu/access/content/attachment/f6b18576-acf9-... Hint. Both power-sizing and indexing will be used. Ć + Question 3. The purchase price of a natural gas-fired commercial boiler (capacity X) was $181,000 eight years ago. Another boiler of the same basic design, except with the capacity 1.42X, is currently being considered for purchase. If it is purchased, some optional features presently costing $28,000 would be added for your application. If the cost index was 162 for this type of equipment when the capacity X boiler was purchased and is 221 now, and the applicable cost capacity factor is 0.8, what is your estimate of the purchase price for the new boiler? Hint: Use both indexing and power-sizing methods. 88 Illinois State University: TEC 330 001 FA2022 - Applied Economic Analysis For...

10

Answer the following questions, to test your understanding of sampling frequency and bit depth. 1. You are part of new automobile design team, and are responsible for designing the sensor data collection system. The specification of the data collection system is that is must be capable of receiving data with a resolution down to 0.1% of full scale (1 part in 1000) for any given sensor. For example, suppose the driver pushes the gas pedal, the motion of which is read by an electronic sensor such that the range of motion is defined from 0 (not pressed) to 1 (fully pressed). If you want 0.1 % accuracy, you need 1000 possible data values between 0 and 1. How many bits do you need to represent data to 0.1% accuracy? Insert a picture of your work.

Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question is Attached in image. Thank you.

:4G 10:48 Shashi Just now Engineering MechanCTE A1 - Lopy - Copy Canspat ibylity Mode- Word (Product Activation Iasiled) INSTRT DESIGN FAGE LAVOUT RETERENCES MAILINGS REVIEW VIEW Times New Ri-|18 KA Aa E-E- E. EE TAaBbCc[ AaBbCc[ AaBbC AaBbCc AaB AuBbCcD AaBbCcC AaBbCcl BIU X, x* A- - A 1 Normai TNo Spac Houding Heading 2 Titte Subtine Subtle Em Enptiat le Paah Set Fas = 0.776 KN (C). Question 2: Determine the force in members BC, CF, and FE. State if the members are in tension or compression. 4 ft B 4 ft 4 ft -4 ft- 600 lb 600 lb 800 lb 3E ENGLISH (UNTED STATES) Nidhi is presenting

SOLVE 1ST QUESTION

please in detaild

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

When ..... a seismic pickup system can be used to measure displacement, velocity, or acceleration .(accelerometer) mass, support stiffness, and O damping parameters are selected and an appropriate transducer is used mass, damping parameters are selected and an appropriate transducer is used mass and damping parameters are selected and an appropriate transducer is used mass, support stiffness, and damping parameters are used

In an industry, the water in a boiler tank needs to be kept at constant pressure, water to the tank comes at constant flow rate and steam is coming from a valve to maintain the pressure. A pressure gauge is used to measure the water pressure in the tank. a. Provide the block diagram representation using a PID controller for the above mentioned condition (Control the pressure using the proportional valve.). b. explain the working principle.

I need answer within 5 minutes please please with my best wishes