Valve Maintenance-6-6

analyze the effect of the density of both liquids to the vertical height of the liquid B

Consider Figure 1, which includes an illustration of the proposed orifice plate meter. The piping isNominal 2 in Schedule 40, the orifice plate radius is 0.5′′ in, and the plate itself is 0.5′′ thick.Flow goes left to right, and to measure pressure losses during flow you will install a differentialpressure sensor along the length that will measure the pressure losses. One port for the differentialsensor will be placed 4′′ upstream (P1 ) and the other port will be placed 15′′ downstream (P3).The distance between the ports will be 19.5′′. The ports will be flush with the inner pipe wall sowe can assume the pressure measured is the fluid pressure at the wall of the pipe If the fluid (viscosity = 0.001 Pa·s and density = 1200 kg/m 3) flows at 1 gpm, estimate thepressure lost over the 19.5′′ span with the orifice plate in place. You should estimate CDfrom Figure 2 and do not neglect pipe friction.C. If we think of this orifice plate as a “fitting,” what is the equivalent length (L/D) e?…

What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?

1) Pitot tube can be used to measure the flow velocity. The equation can be derived from Bernoulli Equation. True or False 2) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 3) The EGL is always a distance V2/2g above the HGL. True or False

what is an air preheater, what are formulas, and their importance, define the diagram, and give me a script on how to explain the design of an air preheater, and how did values end up in that number. based on standards

Q3)Explain how can we use the Linear Variable Differential Transformer (LVDT) as a. A flow measuring device.b. A pressure measuring devicec. A force measuring device

can you help me with part b) please

Using the chart in figure 37.88, what is the velocity and friction loss of a 400 company airstream that is flowing through a 9 inch round duct?

8. Which of the following is not a flow meter classification? Flow measurement by volume Flow measurement by mass Flow measurement by length None of these

Industrial Pipes In order for there to be interchangeability between different components of a pipe, is it necessary that both the pressure class and the gauge are the same?

Solve ASAP.

https://us.humankinetics.com/blogs/excerpt/managing-air-pollution-for-athletes In the literature review, they should present the system installed and the main results obtained. In other words, the enhancement due to the installed system. They have to define the system used in this study. (the report talking about ventilation) pls in briefly Don’t using chatgpt please urgent

can you help me with part a) please

A-Given that the volumetric flow rate for a fluid within a circular cross-section tube can be represented by #HAP 8pL Q where r is the tube radius, u is the fluid viscosity, P is the pressure drop across the tube, and L is the tube length, calculate the pressure drop across a tube of length 1 m and diameter of 23 mm. The fluid is blood (μ = 0.0035 N.s/m²) and has a volumetric flow rate of 4.5 L/min. Assuming the same conditions, what would the required pressure drop be for water (u= 0.001 N.s/m²) and chocolate syrup (u = 150 N.s/m²).

https://us.humankinetics.com/blogs/excerpt /managing-air-pollution-for-athletes In the literature review, they should present the system installed and the main results obtained. In other words, the enhancement due to the installed system. They have to define the system used in this study. (the report talking about ventilation) pls in briefly Don't using chatgpt please very urgent

Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.

A cylinder is configured with a flow control valve to meter-out during extension. The cylinder is a 2" bore and 1" rod. The pump flow rate is 5 gpm with a pressure reducing valve set to 1500 psi. The load is 500 lbs. If the extension speed is to be limited to 10 in/s, what pressure would be measured on the retraction side of the cylinder, during extension? Enter a whole number.Answer:  1,788 ± 10.

1. We can measure the velocity of a flow by using a pitot tube. (True or False) 2. It is the study of the thermodynamic properties of air. 3. A pressure transducer that utilizes an elastic element that usually oval in shape. It is fixed on one end and the displacement caused by pressure at the free end is measured.