A stream of air at 35.0°C and a gauge pressure of 0.400 atm (Stream 1) flows into a pipe passing through a heater, emerges at 77.0°C and 0.200 atm (gauge), and splits into two streams. Stream 2 passes out of the system, and Stream 3 goes through another heater and emerges at 160.0°C and 0.050 atm (gauge). Flowmeters mounted in streams 1 and 2 show readings of 3120 L/min and 1940 L/min respectively. What should the flowmeter for Stream 3 read after the stream emerges from the heater?

A stream of air at 35.0°C and a gauge pressure of 0.400 atm (Stream 1) flows into a pipe passing through a heater, emerges at 77.0°C and 0.200 atm (gauge), and splits into two streams. Stream 2 passes out of the system, and Stream 3 goes through another heater and emerges at 160.0°C and 0.050 atm (gauge). Flowmeters mounted in streams 1 and 2 show readings of 3120 L/min and 1940 L/min respectively. What should the flowmeter for Stream 3 read after the stream emerges from the heater?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q: The sunwheel D has 20 teeth, the gear B is 50 teeth, internal gear C is fixed. The input shaft rotates at 2100 r.p.m. Determine the speed of the output shaft and the torque required to fix C when the gears are transmitting 30 kW. Output shaft Input shaft D
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 84cm and 35cm respectively. If driven shaft runs with 10 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 6mm
Alert for not submit AI generated answer. I need unique and correct answer. Don't try to copy from anywhere. Do not give answer in image formet and hand writing
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts.
18
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
Please solve quickly
1. Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 in. The addendum equals the module, and the clearance equals 0.15 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles.
Solve 10 mins plzzzzz....This is the answer only write hand written plz.... I'll give you multiple upvote
The dimensional limits on a shaft of 25h7 are, (a) 25.000, 25.021 mm (b) 25.000, 24.979 mm (c) 25.000, 25.007 mm (d) 25.000, 24.993 mm