ECT226_Final_Project_Report_Template

Explain how the Active Low Pass Filter works in detail, as shown in a drawing

ASAP It is a type of diode where it operates as a variable resistor when heated.   Your answer       What is the modulation index in ideal condition of AM.   Your answer       A form of AM where a sideband is filtered after its carrier is eliminated.   Your answer       What is the form of AM that used to transmit video signals of the TV system?   Your answer       It is a circuit in the superheterodyne receiver that adds and subtracts the frequencies of the AM signal and the local oscillator frequency.           It is the extent to which the amplitude of the carrier wave is varied by modulating wave.

Bandwidth of an active filter is related to  A.   the size of filter memory   B.   size of filter capacity in term of frequency   C.   size of filter accuracy in term of frequency   D.   filter capability to amplify its gain

pls provide complete solution 15. .Answer= % r = 8.3%, % r=3.1%

Brief explanation of kalman filter

write a full report(2000) words about kalman filter

3. What role does the RC time constant play in a filter circuit ?. In designing of a filter following a rectifier the RC time constant is desired to be long. Why this is so ?

A:11 A docs.google.com For positive half of the signal below, what is the peak output value of the circuit? NOTE: use silicon diode. * 20 V 10V -20 V O 3.3 O -10.3 50.7 29.3 32.3 like that of the clipper, the shape of the input signals of a clamper is changed. * O F От For the given circuit for a 40 V (p-p) sinusoidal input vi, what is the value of vi at which the clipping begIs: v-ov. NOTE: use

a) Design a Butterworth band-pass filter using the TL084 amplifier and draw it with the following specifications:Lower frequency= 60 HzUpper Frequency = 5K HzQ=?Resonant frequency =?

1. The purpose of the Lag Compensator is: I. Improve the study state response of the close system. II. Speed up the transit response. III. All the above. IV. None of the above.  2. In the Lead Compensator:  I. Z > P. II. Z < P. III. Z = P. IV. None of the above.

Design an ACTIVE band-pass filter for the midrange part of a loudspeaker so that the bandpass region is 400 Hz-2000 Hz (as defined by the -3dB points). Design the circuit so that the absolute gain is 2. a. Draw the circuit diagram and specify the resistor and capacitor values. Assume you can use either 100, 330, 500, or 1000 Ohm resistors and can select any value of capacitor. b. Sketch the frequency response (Gain [dB] vs. frequency (Hz)). Note that you will need to convert your gain to dB before plotting. Magnitude (dB) 15 10 5 midrange 12 1 -5 -10 -15 -20 -25 10 100 1,000 Frequency (Hz) 10,000 100,000

Solve using the concpts of Digital Signal ProcessingShow each formula wherever necessary and please show all the steps of the design process

3. A 500-μF capacitor provides a load current of 200 mA at 8% ripple. Calculate the peak rectified voltage obtained from the 60-Hz supply and the DC voltage across the filter capacitor. 4. Calculate the size of the filter capacitor needed to obtain a filtered voltage with 7% ripple at a load of 200 mA. The full-wave rectified voltage is 30 V dc and the supply is 60 Hz. 5. A simple capacitor filter has an input of 40 V dc. If this voltage is fed through an RC filter section (R = 502, C = 40 μF), what is the load current for a load resistance of 500 ?

An RC filter stage (R = 33 Ω, C = 120 μF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.

Circuit Theory - Explain in detail

Choose the correct statement(s) that describe the diagram below. Yol) Bandpass filter Envelope detector Limiter Differentiator Select one or more Ca. FM Discriminator with bandpass limiter El b Narrowband to wideband conversion J FM Demodulator PM Demodulator B.e. Linear PLL model

Give the different types of filters and briefly discuss each

How should I find worst case values of Rin and Rf?

Please assist with question 14 c, d, and e with details on how to do it. Thank you.

Answer just the viva questions pls!

Q3/ Analyze and explain with drawing the sigma-delta ADC work?

if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz .. . = then find , Cutoff frequency 1000O 2000 O 3000O 4000 O

The output power of filter is 100 mW, when the signal frequency is 5 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ?

Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)

Give me the ans step by step with explanation...

i need the answer quickly

H.W: A resistor of resistance R=1000 2is maintained at 17 °C and it shunted by 100 uH inductor. Determine the ms noise voltage across the inductor over a frequency bandwi dth of: Ans: 182 x10° volt Ans: 9.22 x10 volt Ans: 2.34 x10 volt i) 15.9 kHz ii) i) 159 kHz 1590 kHz

i need the answer quickly

Can you solve this question please

Can I get a step by step please? TIA...

Consider two types of digital filters: Butterworth and Elliptic. (c) Comment on the difference between your two designed filters (incl. comparison of filter order, transition band, ripple and phase response).