Dark Modern Gradient 5 Step Sales Process Infographic

Describe the differences between an LNA, a power amp, and a gain block.

How to design a differential input single-ended output opamp that meets these requirements? please include the value width and length of each transistor.

1

Q1) assume A/D converter of counter type uses clock with 100 kHz counter of 8 bit A)determine the total conversion time B)determine the conversion time that is required to generate the sample (111110000)

Design 3-bit Binary Weighted digital to analog converter (DAC) with, R, R=15K2 and Vin =10

refer image

The shown sampled signal is the output of the ADC of Arduino Uno, calculate: 1- The number of samples (N) that needs to calculate Ts. 2- The normalized values for the shown max and min (normalized to 5 V). 3- The signal frequency if the sampling time of Arduino ADC is: Ts=112usec. 1020 35

b. Design 4-bit Binary Weighted digital to analog converter (DAC) with, R, = R = 10 KQ and V = 5V. in

I need fast plz

Calculate the output impedance for small-signal equivalent circuit. (R=10 k2, r. =10 k2) ER Rout O A) Rout = 3.3 ka O B) Rout = 20 ko )C) Rout = 30 ka DI Rout = 5 k0

(b) Design a 6-bit binary weighted resistor DAC for the input of (101100)2. Assume Input Reference voltage, Vref = -1V DC, R = 1kN, Rf= 5.1k2

1. Which of the following is a type of error associated with digital-to-analog converters (DACs)?  A. nonmonotonic error   B. incorrect output codes C. offset error D. nonmonotonic and offset error   2. A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 0101. A. 0.3125 V   B. 3.125 V   C. 0.78125 V D. –3.125 V   3.  A binary-weighted digital-to-analog converter has an input resistor of 100 k. If the resistor is connected to a 5 V source, the current through the resistor is:   A. 50 A B. 5 mA C. 500 µA D. 50 mA    4.  What is the resolution of a digital-to-analog converter (DAC)? A. It is the comparison between the actual output of the converter and its expected output.  B. It is the deviation between the ideal straight-line output and the actual output of the converter.  C. It is the smallest analog output change that can occur as a result of an increment in the digital input.  D. It is its ability to resolve between…

The Current amplification factor is______________

Choose the true option please..as fast as you can please

Q) The static characteristics of the measurement instrument are act -- The linearity of the output. The relation between input and output. The nonlinearity of the output. O Not all above.

1.a)What are the input characteristics of the transducer? b)What is zero error of the transducer? c)List five (5) different transfer characteristics of a transducer.

Summary of instrumentation amplifier

describe and compare the different types of Analog to Digital Converters(Advantages, Disadvantages, Max Resolution, Max Sample Rate and Main Applications). Note: Please do not handwriting and write an average information for each type.

signal system subject  use intergration and prove it with graph

QI/Design a binary to Gray converter using a four- input, four-output PROM ?

Explain the working of Binary Weighted Resistor Digital to Analog converter with a neat diagram. pleas writing not typing

Sketch the output of the following MOSFET sampling curvuit

A FET   a. has a very large voltage gain   b. has a low input impedance   c. is a voltage controlled device   d. is a current controlled device

A certain counting type 12 bit ADC operates with FSR = 0 to 10 V and clock frequency folk = 1 MHz. Determine the dynamic range of the converter, conversion time, conversion rate and Nyquist frequency of the converter.

Design Question Vref Rref RG RM A1 VOUT Digital DAC1 Input, DIN H n VDAC Figure 1 Figure 1 shows the circuit used to condition the output of the n – bit Digital to Analog Converter “DAC1" having a digital input value of Din. DAC1 may be assumed to have a voltage output with zero source resistance coded in “straight binary" such that For a binary input of DIN = 000...000 the output voltage VDAC is 0V For a binary input of Din= 111...111 the output voltage vDAC is Vref Where Vref is a positive voltage reference. (c) Hence show that the error in vour due to opamp DC input current and voltage errors including both bias and offset currents is given by: voute = 2Vos + IB|2RM – Rref|+Ios(2RM) %3D

question in photo please

. What is the largest value of output voltage from an 8-bit DAC that produces 1.0V for a digital input of 00110010?

Vertical Amplifier is used in CRO to Select one: a. Amplify signal from input b. Delay the input signal C. Amplify signal from Time base generator d. Initiate the time base generator

Draw drain current and transconductance of VDD M1 as function of input voltage Vin. RD Vout Vin HEM,

Calculate the input im pedance for small-signal equivalent circuit. Circuit Parameters / Devre Parametreleri R1=9 k2, R2=14 kN, r =24 ko Vc J' R1 R2추 Rin O a. 17,842 kO O b. 24,087 kO O c. 27,655 ko O d. 31,224 kO e. 11,597 ko

Explain wein bridge oscillator in detail. give its advantages and disadvantages in detail