Concept explainers
8.121 and 8.123 A cable is placed around three parallel pipes. Two of the pipes are fixed and do not rotate; the third pipe is slowly rotated. Knowing that the coefficients of friction are μS = 0.25 and μk = 0.20, determine the largest weight W that can be raised (a) if only pipe A is rotated counterclockwise, (b) if only pipe C is rotated clockwise.
Fig. P8.120 and P8.121
(a)
Find the largest weight W that can be raised only when the pipe A is rotated counter clockwise.
Answer to Problem 8.121P
The largest weight W that can be raised only when the pipe A is rotated counter clockwise is
Explanation of Solution
Given information:
The coefficient of static friction is
The coefficient of kinetic friction is
Calculation:
Show the free-body diagram of the pipes A, B, and C as in Figure 1.
Find the angle of the cable wounded around the pipe as follows;
Find the largest weight W using the equation.
Substitute 0.25 for
Therefore, the largest weight W that can be raised only when the pipe A is rotated counter clockwise is
(b)
Find the largest weight W that can be raised only when the pipe C is rotated clockwise.
Answer to Problem 8.121P
The largest weight W that can be raised only when the pipe C is rotated clockwise is
Explanation of Solution
Given information:
The coefficient of static friction is
The coefficient of kinetic friction is
Calculation:
Show the free-body diagram of the pipes A, B, and C as in Figure 2.
Find the angle of the cable wounded around the pipe as follows;
Find the largest weight W using the equation.
Substitute 0.25 for
Therefore, the largest weight W that can be raised only when the pipe C is rotated clockwise is
Want to see more full solutions like this?
Chapter 8 Solutions
VECTOR MECH....F/ENGNRS-STATICS -CONNECT
- 60 mm 15 mm 50 mm E 500 mm 8.31 A pipe of diameter 60 mm is gripped by the Stillson wrench shown. Portions AB and DE of the wrench are rigidly attached to each other, and portion CF is connected by a pin at D. If the wrench is to grip the pipe and be self-locking, determine the required minimum coefficients of friction at A and C. F Fig. P8.31 Barrow_forwardPlease solve the question in handwriting step by step.arrow_forward8.50 and 8.51 Two 6° wedges of negligible weight are used to move and position the 900-kg block. Knowing that the coefficient of static friction is 0.30 at all surfaces of contact, determine the smallest force P that should be applied as shown to one of the wedges. Fig. P8.50 900 kgarrow_forward
- A lever of negligible weight is loosely fitted onto a 75-min-diameter fixed shaft. It is observed that the lever will just start rotating if a 3-kg mass is added at c . Determine the coefficient of static friction between the shaft and the lever.arrow_forwardProblem 8.33 The man having a weight of 200 lb pushes horizontally on the crate. The coefficient of static friction between the 450-lb crate and the floor is μ = 0.3 and between his shoes and the floor is μ's = 0.6. Determine if the man can move the crate. Part A Determine the force that tends to move the man to the right. Express your answer to three significant figures and include the appropriate units. Part B Determine the magnitude of the maximum force due to friction that opposes the tendency of the man's motion. Express your answer to three significant figures and include the appropriate units. Part C Can he move the crate? Explain your reasoning. 10 of 10 3 ftarrow_forwardPROBLEM 8.23 The 10-lb uniform rod AB is held in the position shown by the force P. Knowing that the coefficient of static friction is 0.20 at A and B, determine the smallest value of P for which equilibrium is maintained. 15 i G 7.5 in. A -8 in. Fig. P8.23arrow_forward
- Q.5arrow_forwardA flat belt connects pulley a, which drives a machine tool, to pulley b, which is attached to the shaft of an electric motor. the coefficients of friction are μs = 0.25 and μk = 0.20 between both pulleys and the belt. knowing that the maximum allowable tension in the belt is 600 lb, determine the largest torque that the belt can exert on pulley aarrow_forwardSolve Prob. 8.126 assuming that 0= 75°.(Reference to Problem 8.126):The strap wrench shown is used to grip the pipe firmly without marring the external surface of the pipe. Knowing that the coefficient of static friction is the same for all surfaces of contact, determine the smallest value of μs for which the wrench will be self-locking when a = 200 mm, r=30 mm, and 0= 65°.arrow_forward
- 3.) Uniform box A has a weight of 40 Ib, and is leaning against box B as shown. Box B has a weight of WB. Friction coefficients between the various 20 in. (friction-less) X = 24 in. Y = 10 in. 30 deg. surfaces are as shown. 24 in. W = 40 Ib u-0.7 H= 0.4 a. Draw FBD's of box A and box B. b. Determine if the system is in static equilibrium. Note – Only check for sliding of A and B. Narrow_forwardA pipe of diameter 60 mm is gripped by the stillson wrench shown. Portions AB and DE of the wrench are rigidly attached to each other, and portion CF is connected by a pin at D. If the wrench is to grip the pipe and be self-locking, determine the required coefficients of friction at A and c.arrow_forwardThe square-threaded worm gear shown has a mean radius of 1.5 in. and a lead of 0.375 in. The large gear is subjected to a constant clockwise couple of 7.2 kip · in. Knowing that the coefficient of static friction between the two gears is 0.12, determine the couple that must be applied to shaft AB in order to rotate the large gear counterclockwise. Neglect friction in the bearings at A, B, and C. ហ n Fig. P8.69 ллллллллллл Pc 12 in. 7.2 kip-in. wwwarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY