P D B Ө

Q: 4. The position of the machine block B is adjusted by moving the wedge A. Knowing that the…

A:

Q: Knowing that the coefficient of static friction is 0.30 between the rope and the horizontal pipe and…

A: (a) Free-body diagram of rope for horizontal and vertical pipes, The contact angle for the…

Q: A safety device used by workers climbing ladders fixed to high structures consists of a rail…

A: First draw the free body diagram of the cam. The frictional force at A is : FA=μsNA The frictional…

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: The radius of shaft r = 2.5/2 inch = 1.25 in. The coefficient of static friction is μs = 0.15 N The…

Q: The cylinder shown is of weight W and radius r, and the coefficient of static friction μs is the…

A: Given data: *The coefficient of static friction is same at A and B μA= μB. *The weight of the…

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of…

A: GivenF=908Nθ=22oμs=0.33

Q: Problem 8.11 Determine the maximum weight W the man can lift with constant velocity using the pulley…

A:

Q: A 5000-lb box is to be lowered by relaxing the force F, which is held by a man to control the decent…

A:

Q: ock A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static…

A: Given data as per question Coefficient of static friction at all surfaces of contact, μs= 0.25 θ =…

Q: A 15° wedge is forced under a 50-kg pipe as shown. The coefficient of static friction at all…

A: Draw the free body diagram for a better understanding of the problem.

Q: PROBLEM 11: A flat belt is used to transmit a couple from pulley A to pulley B. The radius of each…

A: The radius of each people is The coefficient of static friction is

Q: PROBLEM 12: A ladder AB leans against a wall as shown. Assuming that the coefficient of static…

A:

Q: 9. A 400 kN block is resting on a rough horizontal surface for which the coefficient of friction is…

A:

Q: Determine the maximum allowable value of weight W at rest. Knowing that the coefficient of static…

A:

Q: A flat belt connects pulley A, which drives a machine tool, to pulley B, which is attached to the…

A:

Q: A 400 kN block resting on a rough horizontal surface for which the coefficient of friction is 0.40.…

A:

Q: The axle of the pulley is frozen and cannot rotate with respect to the block. Knowing that the…

A:

Q: A lever AB of negligible weight is loosely fitted onto a 2.5-in.-diameter fixed shaft. Knowing that…

A: Given: The diameter of the shaft, d = 2.5 in The coefficient of friction between shaft and lever, μ…

Q: The three bars have a weight of WA = 20 lb, WB = 40 lb, and W. = 60 lb, respectively. If the…

A:

Q: shown, a man is leaning against the side of a cabinet with an unusual design. The cabinet's main…

A:

Q: Can the system in given figure be in static equilibrium in the position shown? The uniform bar AB…

A: Given: The length of the bar→L=5 m Weight of the bar AB→WAB=500 lb Weight of the block C→WC=300 lb…

Q: Problem 8.26 The block brake is used to stop the wheel from rotating when the wheel is subjected to…

A: M0 = 440 N-mµs = 0.6

Q: A hot-metal ladle and its contents weigh 130 kips. Knowing that the coefficient of static friction…

A: Given Data Diameter of bearings, D=16 in Radius of bearing ,R=8 in Coefficient of static friction,…

Q: What weight W must be suspended through a fixed pulley shown to start motion to the left of the…

A:

Q: B 60 mm 15 mm- 50 mm E 500 mm 8.31 A pipe of diameter 60 mm is gripped by the Stillson wrench shown.…

A:

Q: A flat belt is used to transmit a couple from pulley A to pulley B . The radius of each pulley is 50…

A:

Q: Problem 8.3 The mine car and its contents have a total mass of 5.1 Mg and a center of gravity at G.…

A: The coefficient of friction is The mass of the car is

Q: The square-threaded worm gear shown has a mean radius of 1.5 in. and a lead of 0.375 in. The large…

A:

Q: is used to control the The band brake of Fig. rotation of a drum. The coefficient of friction…

A: Draw free-body diagram of a handle,   Apply moment equilibrium about hinge point,   ∑MHinge=0T175…

Q: Knowing that the coefficient of static friction is 0.25 between the rope and the horizontal pipe and…

A: Given Data T=400 N The coefficient of static friction,μ1= 0.25 (between the rope and the horizontal…

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.