(a)
The average power of the elevator motor.
(a)
Answer to Problem 38P
The average power of the elevator motor is
Explanation of Solution
Write the expression for average power
Here,
Consider the elevator as an isolated system.
Write the expression for work done by the motor on the elevator
Simplify the above expression.
Here,
Since the direction of force and displacement is same, hence the angle
Substitute
Simplify the above equation
Substitute
Write the expression for total force when the system is moving with an acceleration.
Here,
Write the expression for total force acting on the system
Here,
Substitute
Consider the elevator as an isolated system and the motion of elevator is by force acting by motor, the elevator starts from rest when a force is applied by motor against the gravitational force of the elevator.
The gravitaional force is negative because it is in opposite to the direction of acceleration.
Write the expression for force due to gravity.
Here,
Substitute
Simplify the above equation.
Consider the motion of elevator from rest to the speed of its cruising speed.
Write the equation of motion for velocity in terms of acceleration and time
Here,
Since the initial speed is zero.
Substitute
Simplify the above equation to find the expression for
Write the equation of motion for distance travelled in terms of acceleration, time and initial speed.
Here,
Since the initial speed is zero.
Substitute
Substitute
Simplify the above equation.
Conclusion:
Substitute
Substitute
Substitute
Substitute
Thus, the average power of the elevator motor is
(b)
The comparison between average power and the power when elevator moves with cruising speed.
(b)
Answer to Problem 38P
The instantaneous power required is
Explanation of Solution
Write the expression for instaneous power when the elevator is moving at a constant cruising speed
Simplify the above expression
Here,
Since the force and velocity are in same direction, hence the angle between
Substitute
Simplify the above equation.
Here,
Since the elevator moves at constant speed when it reaches cruising speed, hence the acceleration will be zero.
Write the expression for comparison in both powers
Here,
Since the elevator is moving at constant speed hence the acceleration is zero.
Substitute
Simplify the above equation
Conclusion:
Substitute
Substitiute
Substitute
Thus, the instantaneous power required is
Want to see more full solutions like this?
Chapter 8 Solutions
Physics for Scientists and Engineers with Modern, Revised Hybrid (with Enhanced WebAssign Printed Access Card for Physics, Multi-Term Courses)
- A 6.50 102-kg elevator starts from rest and moves upward for 3.00 s with constant acceleration until it reaches its cruising speed, 1.75 m/s. (a) What is the average power of the elevator motor during this period? (b) How does this amount of power compare with its power during an upward trip with constant speed?arrow_forwardA certain automobile engine delivers 2.24 104 W (30.0 hp) to its wheels when moving at a constant speed of 27.0 m/s ( 60 mi/h). What is the resistive force acting on the automobile at that speed?arrow_forwardA student expends 7.5 W of power in lifting a textbook 0.50 m in 1.0 s with a constant velocity. (a) How much work is done, and (b) how much does the book weigh (in newtons)? The answers to Confidence Exercises may be found at the back of the book.arrow_forward
- A 537-kg trailer is hitched to a truck. Find the work done by the truck on the trailer in each of the following cases. Assume rolling friction is negligible. a. The trailer is pulled at constant speed along a level road for 2.30 km. b. The trailer is accelerated from rest to a speed of 88.8 km/h. c. The trailer is pulled at constant speed along a road inclined at 12.5 for 2.30 km.arrow_forwardA loaded ore car has a mass of 950 kg and rolls on rails with negligible friction. It starts from rest and is pulled up a mine shaft by a cable connected to a winch. The shaft is inclined at 30.0 above the horizontal. The car accelerates uniformly to a speed of 2.20 m/s in 12.0 s and then continues at constant speed. (a) What power must the winch motor provide when the car is moving at constant speed? (b) What maximum power must the winch motor provide? (c) What total energy has transferred out of the motor by work by the time the car moves off the end of the track, which is of length 1 250 m?arrow_forward“ E=K+Uconstant is a special case of the work energy theorem.” Discuss this statement.arrow_forward
- A cyclist in a race must climb a 5 hill at a speed of 8 m/s. If the mass of the bike and the biker together is 80 kg, what must be the power output of the biker to achieve the goal?arrow_forwardA 100 — kg man is skiing across level ground at a speed of 8.0 m/s when he comes to the small slope 1.8 m higher than ground level shown in the following figure. (a) If the skier coasts up the bill, what is his speed when he reaches the top plateau? Assume friction between the snow and skis is negligible. (b) What is his speed when he reaches the upper level if an 80 — N frictional force acts on the skis?arrow_forwardA 500-kg dragster accelerates from rest to a final speed of 110 m/s in 400 m (about a quarter of a mile) and encounters an average frictional force of 1200 N. What is its average power output in watts and horsepower if this takes 7.30s?arrow_forward
- Repeat the preceding problem, but this time, suppose that the work done by air resistance cannot be ignored. Let the work done by the air resistance when the skier goes from A to B along the given hilly path be —2000 J. The work done by air resistance is negative since the air resistance acts in the opposite direction to the displacement. Supposing the mass of the skier is 50 kg, what is the speed of the skier at point B ?arrow_forwardA sled of mass 70 kg starts from rest and slides down a 10 incline 80 m long. It then travels for 20 m horizontally before starting back up an 8° incline. It travels 80 m along this incline before coming to rest. What is the magnitude of the net work done on the sled by friction?arrow_forwardAs shown in Figure P7.20, a green bead of mass 25 g slides along a straight wire. The length of the wire from point to point is 0.600 m, and point is 0.200 in higher than point . A constant friction force of magnitude 0.025 0 N acts on the bead. (a) If the bead is released from rest at point , what is its speed at point ? (b) A red bead of mass 25 g slides along a curved wire, subject to a friction force with the same constant magnitude as that on the green bead. If the green and red beads are released simultaneously from rest at point , which bead reaches point first? Explain. Figure P7.20arrow_forward
- College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781938168000Author:Paul Peter Urone, Roger HinrichsPublisher:OpenStax CollegePhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning