Concept explainers
a)
The final temperature in each tank A and tank B.
a)
Answer to Problem 201RP
The final temperature in tank A is
The final temperature in tank B is
Explanation of Solution
Write the formula to calculate the specific volume of steam from tables
Here, specific volume of saturated liquid is
Write the formula to calculate the specific internal energy of steam from tables
Here, specific internal energy of saturated liquid is
Write the formula to calculate the specific entropy of steam from tables
Here, specific entropy of saturated liquid is
Write the formula to calculate the mass of the steam
Here, volume of the steam is
Write the expression for the mass balance.
Here, mass of the water entering into the system is
Write the expression for the energy balance Equation for a closed system.
Here, net energy transfer into the control volume is
Conclusion:
From Table A-5, “Saturated water-Pressure table”, obtain the following properties of water at initial pressure
Substitute
Substitute
Substitute
From Table A-5, “Saturated water-Pressure table”, obtain the following properties of water at final pressure
Here, final temperature of steam in tank A is
The steam in tank A undergoes isentropic process, Thus final specific entropy of steam in tank A
Substitute
Substitute
Substitute
From Table A-6, “Superheated water”, note the properties for steam in tank B initially at the pressure of
Substitute
Substitute
Substitute
Rewrite the Equation (V) to calculate the final total mass of steam in tank B
Here, initial mass of steam in tank B is
Substitute
Substitute
Substitute
From first law of thermodynamics, Re-write the Equation (VI) for heat transfer
Here, work done is
Substitute
From Table A-5, “Saturated water-Temperature table”, obtain the following properties of water at
Here, the temperature of the steam in tank at final state is
Thus, the final temperature of steam in tank A is
b)
The entropy generated during the process.
b)
Answer to Problem 201RP
The entropy generated during the process is
Explanation of Solution
Write the expression for the entropy balance Equation of the system.
Here, rate of net entropy in is
Conclusion:
Re-write the Equation (IX) for the entropy generated
Here, temperature of the surroundings is
Substitute
Thus, the entropy generated during this process is
Want to see more full solutions like this?
Chapter 7 Solutions
CONNECT FOR THERMODYNAMICS: AN ENGINEERI
- Two rigid tanks are connected by a valve. Tank A contains 0.25 m³ of water at 450 kPa and 75 percent quality. Tank B contains 0.55 m³ of water at 300 kPa and 250°C. The valve is now opened, and the two tanks eventually come to the same state. Determine the pressure and the amount of heat transfer when the system reaches thermal equilibrium with the surroundings at 25°C. Show your complete solution.arrow_forwardSteam enters a two-stage adiabatic turbine at 8 MPa and 500°C. It expands in the first stage to a state of 2 MPa and 350°C. Steam is then reheated at constant pressure to a temperature of 500°C before it is routed to the second stage, where it exits at 30 kPa and a quality of 97 percent. The work output of the turbine is 5 MW. Assuming the surroundings to be at 25°C, determine the reversible power output and the rate of exergy destruction within this turbine.arrow_forwardTwo rigid tanks are connected by a valve, as shown in Figure Q3 below. Tank A is insulated and contains 0.2 m3 of steam at 400 kPa and 80 percent quality. Tank B is uninsulated and contains 3 kg of steam at 200 kPa and 250°C. The valve is now opened, and steam flows from tank A to tank B until the pressure in tank A drops to 300 kPa. During this process 600 kJ of heat is transferred from tank B to the surroundings at 0°C. Assuming the steam remaining inside tank A to have undergone a reversible adiabatic process, 600 kJ A B 0.2 m3 3 kg steam steam 400 kPa 200 kPa x = 0.8 250°C Figure Q3 (a) Calculate the final temperature in tank A. (b) Calculate the quality of the steam in tank A at 300 kPa.arrow_forward
- A well-insulated 4-m * 4-m * 5-m room initially at 10C is heated by the radiator of a steam-heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200C. At this moment both the inlet and the exit valves to the radiator are closed. A 120-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 30 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature, determine (a) the average temperature of air in 30 min, (b) the entropy change of the steam, (c) the entropy change of the air in the room, and (d) the entropy generated during this process, in kJ/K. Assume the air pressure in the room remains constant at 100 kPa at all times.arrow_forwardA rigid, insulated tank that is initially evacuated is connected through a valve to a supply line that carries steam at 4 MPa. Now the valve is opened, and steam is allowed to flow into the tank until the pressure reaches 4 MPa, at which point the valve is closed. If the final temperature of the steam in the tank is 550°C, determine the temperature of the steam in the supply line and the flow work per unit mass of the steam.arrow_forwardThe pressure of saturated water vapor in an insulated tank with a volume of 5.7 m3 is 350 kPa. The tank is connected to the superheated steam pipe with a valve. The pressure of the superheated steam flowing in the pipe is 2.8 MPa and the temperature is 580oC. By opening the valve, the pressure of the water vapor in the tank is filled until it reaches 2.8 MPa. Calculate the second law efficiency of the filling process.arrow_forward
- An insulated piston cylinder assembly initially contains 5 L of saturated liquid water at a constant pressure of 175 kPa. There is an electric heater and a mixer inside the cylinder. Then the water is mixed for 45 minutes on the one hand and heated by a heater with 8 A current flowing through it on the other hand. During this process at constant pressure, half of the liquid evaporates and 400 kJ of work is done by the mixer. Plot the potential of the electrical source on the P-v diagram.arrow_forwardA rigid tank of 0.22-m volume initially contains saturated vapor refrigerant-134a at 1.2 MPa. The tank is connected by a valve to a supply line that carries refrigerant-134a at 1.6 MPa and 46 C. The valve is opened, and the refrigerant is allowed to enter the tank. The valve is closed when it is observed that the tank contains saturated liquid at 1.6 MPa. Determine (a) the mass of the refrigerant that has entered the tank and (b) the amount of heat transfer.arrow_forwardThermodynamicsarrow_forward
- A rigid tank initially contains 0.9 kg of water. Then it is filled more with steam from a supply line at 1.5 MPa and 320°C until the pressure in the tank reaches to the supply pressure (1.5 MPa) at 360°C. The final mass in the tank is 2 kg and the process is adiabatic. • Calculate the initial specific internal energy of the water. • Comment on the initial phase of the water. Is it mixture or superheated or?. steam supply line initially 0.9 kg waterarrow_forward3 A 40-L electrical radiator containing heating oil is placed in a 50-m³ room. Both the room and the oil in the radiator are initially at 10°C. The radiator with a rating of 2.4 kW is now turned on. At the same time, heat is lost from the room at an average rate of 0.35 kJ/s. After some time, the average temperature is measured to be 20°C for the air in the room, and 50°C for the oil in the radiator. Taking the density and the specific heat of the oil to be 950 kg/m3 and 2.2 kJ/kg-°C, respectively, determine how long the heater is kept on. Assume the room is well sealed so that there are no air leaks. The gas constant of air is R = 0.287 kPa-m³/kg-K (Table A-1). Also, c = 0.718 kJ/kg-K for air at room temperature (Table A-2). Oil properties are given to be p = 950 kg/m³ and Cp = 2.2 kJ/kg.°C. 3 10°C Room Radiator The heater is kept on for Q min. 4arrow_forwardA 5-ft3 rigid tank initially contains refrigerant-134a at 60 psia and 100 percent quality. The tank is connected by a valve to a supply line that carries refrigerant-134a at 140 psia and 80°F. The valve is now opened, allowing the refrigerant to enter the tank, and is closed when it is observed that the tank contains only saturated liquid at 100 psia. Determine the mass of the refrigerant that entered the tank.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY