In flow over a surface, velocity and temperature profiles are of the forms
where the coefficients A through G are constants. Obtain expressions for the friction coefficient
Want to see the full answer?
Check out a sample textbook solutionChapter 6 Solutions
Fundamentals of Heat and Mass Transfer
Additional Engineering Textbook Solutions
Engineering Mechanics: Statics
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Degarmo's Materials And Processes In Manufacturing
Statics and Mechanics of Materials (5th Edition)
Manufacturing Engineering & Technology
Engineering Mechanics: Dynamics (14th Edition)
- Q-4 The apparatus shown in the figure is used to measure the velocity of air at the center of a duct having a 10 cm diameter. A tube mounted at the center of the duct has a 2 mm diameter and is attached to one leg of a slant-tube manometer. A pressure tap in the wall of the duct is connected to the other end of the slant-tube manometer. The well of 10 cm p = 150 kPa T= 20°C the slant-tube manometer is sufficiently large that the elevation of the fluid in it does not change significantly when fluid moves up the leg of the manometer. The air in the duct is at a temperature of 20°C, and the pressure is 150 kPa. The manometer liquid has a specific gravity of 0.7, and the slope of the leg is 30°. When there is no flow in the duct, the liquid surface in the manometer lies at 2.3 cm on the slanted scale. When there is flow in the duct, the liquid moves up to 6.7 cm on the slanted scale. Find the velocity of the air in the duct. Assuming a uniform velocity profile in the duct, calculate the…arrow_forwardCOnsider an airplane flying at a standard altitude of 6km with a velocity of 330m/s. At a point on the wing of the airplane, the velocity is 400m/s. Calculate the pressure at this point. Cp=1008 j/kgK. answer should be in metric. and detailed solution.arrow_forwardplease do parts F through Jarrow_forward
- Consider the following schematics for a sudden expansion in a pipe.(a) Using the mass and momentum balances to show that there is an overall increaseof pressure equal to the equation in the image.(b) Use energy balance to show that the frictional dissipation is like the equation shown in the image(c) For a constant u1 and A1, show that the pressure rise (P2 - P1) is a maximumwhen the diameter of the larger pipe is √2 times the fixed diameter of the smaller pipe,i.e., A2 = 2A1.arrow_forwardThe friction coefficient for a boundary layer is given by the expression: Cf= If the average flow velocity increases from an original state to a new state by a factor of 4.66, calculate the ratio of the Cf over its value at the original state. 1.32 √Rexarrow_forward(1) Given the working form of the Bernoulli equation as v2 + gz + dW - F dm Where s is the friction heating per unit mass dQ F = Au dm Given also that friction heating in laminar flow of Newtonian fluids in circular pipes is given as -AP F = = -gAz = Q Ax µ 128 Ax is change in the x-direction. A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m'. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometerarrow_forward
- Initially, 10 m³ gas is stored at 270185 Pa pressure. Then it is compressed to 3 m³ at 5x105 Pa pressure. Then the bulk modulus of the fluid is _N/m?. 32830.7 4690.1 O 725361.4 328307.1arrow_forwardA Pitot-static probe connected to a differential pressure gage is used to measure the airvelocity in a duct. If the air is at 13.4 psia absolute and 70°F and the reading of thedifferential pressure gage is 0.15 psi, determine the air velocity. Ans. 143 ft/s please write a clear solution for thisarrow_forwardSolve for the latent heat of water at Tw = 28C(and. λw = 2435 kJ/kg)arrow_forward
- heat lost by aluminum cup: -2160 J Mass of ice cube : 5.76 change in entropy for ice as melts: 7.03 J/k change in entropy for the melted water as it warms up: 0.87J/K Calculate the change in entropy for aluminum cup (J/k) Calculate the total change in entropy for entire system (J/k)arrow_forwardAn ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the enthalpy per unit mass at the inlet, h1__________(kJ/kg)arrow_forwardAn ideal gas passes a diffuser. At the diffuser inlet, the temperature is T1 = 350.00 K, the pressure P1 = 100.00 kPa, the velocity V1 = 200.00 m/s, and the inlet area A1 = 0.30 m2. At the exit, the velocity is very small. The specific heat of the ideal gas at the constant pressure is cp = 1.0050 kJ/(kg·K). The gas constant is R = 0.2870 kPa·m3/(kg·K). Determine the enthalpy per unit mass at the exit, h2__________(kJ/kg)arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning