THERMODYNAMICS-SI ED. EBOOK >I<
9th Edition
ISBN: 9781307573022
Author: CENGEL
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5.5, Problem 70P
Consider a steady-flow heat exchanger involving two different fluid streams. Under what conditions will the amount of heat lost by one fluid be equal to the amount of heat gained by the other?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Saturated propane vapor at 2:00 x 102 psia is fed to a well-insulated heat exchanger at a rate of 3:00 x 103 SCFH (standard cubic feet per hour). The propane leaves the exchanger as a saturated liquid (i.e., a liquid at its boiling point) at the same pressure. Cooling water enters the exchanger at70°F, flowing cocurrently (in the same direction) with the propane. The temperature difference between the outlet streams (liquid propane and water) is 15°F.(a) What is the outlet temperature of the water stream? (Use the Antoine equation.) Is the outlet water temperature less than or greater than the outlet propane temperature? Briefly explain.(b) Estimate the rate (Btu/h) at which heat must be transferred from the propane to the water in the heat exchanger and the required flow rate (lbm/h) of the water. (You will need to write two separate energy balances.) Assume the heat capacity of liquid water is constant at 1.00 Btu/(lb m°F) and neglect heat losses to the outside and the effects of…
Air (Cp = 1005 J/kg °C) enters a cross-flow heat exchanger at 10 C at a rate of 3 kg/s, where it is heated by a hot water stream (Cp = 4190 J/kg °C) that enters the heat exchanger at 95 °C at a rate of 1 kg/s. Determine the maximum heat transfer rate and the outlet temperatures of the cold and the hot water streams for that case.
A thin-walled, double-tube, counterflow heat exchanger is used to cool oil (Cp = 2.20 kJ/kg °C) from 150 to 40°C at a rate of 2 kg/s by means of water (Cp = 4.18 kJ/ kg °C), which enters at 22°C at a rate of 1.5 kg/s. Determine the rate of heat transfer in the exchanger and the leaving temperature of the water.
Chapter 5 Solutions
THERMODYNAMICS-SI ED. EBOOK >I<
Ch. 5.5 - Name four physical quantities that are conserved...Ch. 5.5 - Define mass and volume flow rates. How are they...Ch. 5.5 - Does the amount of mass entering a control volume...Ch. 5.5 - Consider a device with one inlet and one outlet....Ch. 5.5 - The ventilating fan of the bathroom of a building...Ch. 5.5 - Air enters a 16-cm-diameter pipe steadily at 200...Ch. 5.5 - A steam pipe is to transport 200 lbm/s of steam at...Ch. 5.5 - A garden hose attached with a nozzle is used to...Ch. 5.5 - A steady-flow compressor is used to compress...Ch. 5.5 - Air enters the 1-m2 inlet of an aircraft engine at...
Ch. 5.5 - A 2-m3 rigid tank initially contains air whose...Ch. 5.5 - Air enters a nozzle steadily at 2.21 kg/m3 and 40...Ch. 5.5 - A spherical hot-air balloon is initially filled...Ch. 5.5 - Water enters the constant 130-mm inside-diameter...Ch. 5.5 - A desktop computer is to be cooled by a fan whose...Ch. 5.5 - A hair dryer is basically a duct of constant...Ch. 5.5 - Refrigerant-134a enters a 28-cm-diameter pipe...Ch. 5.5 - What are the different mechanisms for transferring...Ch. 5.5 - How do the energies of a flowing fluid and a fluid...Ch. 5.5 - An air compressor compresses 6 L of air at 120 kPa...Ch. 5.5 - A house is maintained at 1 atm and 24C, and warm...Ch. 5.5 - Refrigerant-134a enters the compressor of a...Ch. 5.5 - Steam is leaving a pressure cooker whose operating...Ch. 5.5 - How is a steady-flow system characterized?Ch. 5.5 - Can a steady-flow system involve boundary work?Ch. 5.5 - A diffuser is an adiabatic device that decreases...Ch. 5.5 - The kinetic energy of a fluid increases as it is...Ch. 5.5 - The stators in a gas turbine are designed to...Ch. 5.5 - The diffuser in a jet engine is designed to...Ch. 5.5 - Air enters a nozzle steadily at 50 psia, 140F, and...Ch. 5.5 - Air at 600 kPa and 500 K enters an adiabatic...Ch. 5.5 - Carbon dioxide enters an adiabatic nozzle steadily...Ch. 5.5 - Steam enters a nozzle at 400C and 800 kPa with a...Ch. 5.5 - Air at 80 kPa and 127C enters an adiabatic...Ch. 5.5 - Air at 13 psia and 65F enters an adiabatic...Ch. 5.5 - Refrigerant-134a at 700 kPa and 120C enters an...Ch. 5.5 - Refrigerant-134a enters a diffuser steadily as...Ch. 5.5 - Air at 80 kPa, 27C, and 220 m/s enters a diffuser...Ch. 5.5 - Air enters an adiabatic nozzle steadily at 300...Ch. 5.5 - Consider an adiabatic turbine operating steadily....Ch. 5.5 - Prob. 42PCh. 5.5 - Somebody proposes the following system to cool a...Ch. 5.5 - Air is expanded from 1000 kPa and 600C at the...Ch. 5.5 - Prob. 45PCh. 5.5 - Refrigerant-134a enters a compressor at 100 kPa...Ch. 5.5 - Refrigerant-134a enters a compressor at 180 kPa as...Ch. 5.5 - Steam flows steadily through an adiabatic turbine....Ch. 5.5 - Steam flows steadily through a turbine at a rate...Ch. 5.5 - Steam enters an adiabatic turbine at 8 MPa and...Ch. 5.5 - An adiabatic air compressor compresses 10 L/s of...Ch. 5.5 - Carbon dioxide enters an adiabatic compressor at...Ch. 5.5 - Steam flows steadily into a turbine with a mass...Ch. 5.5 - Air is compressed by an adiabatic compressor from...Ch. 5.5 - Air enters the compressor of a gas-turbine plant...Ch. 5.5 - A portion of the steam passing through a steam...Ch. 5.5 - Why are throttling devices commonly used in...Ch. 5.5 - Would you expect the temperature of air to drop as...Ch. 5.5 - During a throttling process, the temperature of a...Ch. 5.5 - Someone claims, based on temperature measurements,...Ch. 5.5 - Refrigerant-134a is throttled from the saturated...Ch. 5.5 - A saturated liquidvapor mixture of water, called...Ch. 5.5 - Prob. 64PCh. 5.5 - A well-insulated valve is used to throttle steam...Ch. 5.5 - Refrigerant-134a enters the expansion valve of a...Ch. 5.5 - Prob. 68PCh. 5.5 - Prob. 69PCh. 5.5 - Consider a steady-flow heat exchanger involving...Ch. 5.5 - Prob. 71PCh. 5.5 - Refrigerant-134a at 700 kPa, 70C, and 8 kg/min is...Ch. 5.5 - Hot and cold streams of a fluid are mixed in a...Ch. 5.5 - A hot-water stream at 80C enters a mixing chamber...Ch. 5.5 - Water at 80F and 20 psia is heated in a chamber by...Ch. 5.5 - An adiabatic open feedwater heater in an electric...Ch. 5.5 - Cold water (cp = 4.18 kJ/kgC) leading to a shower...Ch. 5.5 - Steam is to be condensed on the shell side of a...Ch. 5.5 - Air (cp = 1.005 kJ/kgC) is to be preheated by hot...Ch. 5.5 - An open feedwater heater heats the feedwater by...Ch. 5.5 - Refrigerant-134a at 1 MPa and 90C is to be cooled...Ch. 5.5 - The evaporator of a refrigeration cycle is...Ch. 5.5 - An air-conditioning system involves the mixing of...Ch. 5.5 - A well-insulated shell-and-tube heat exchanger is...Ch. 5.5 - Steam is to be condensed in the condenser of a...Ch. 5.5 - Steam is to be condensed in the condenser of a...Ch. 5.5 - Two streams of water are mixed in an insulated...Ch. 5.5 - Two mass streams of the same ideal gas are mixed...Ch. 5.5 - Water is heated in an insulated, constant-diameter...Ch. 5.5 - A 110-volt electrical heater is used to warm 0.3...Ch. 5.5 - The ducts of an air heating system pass through an...Ch. 5.5 - The fan on a personal computer draws 0.3 ft3/s of...Ch. 5.5 - Saturated liquid water is heated in a steady-flow...Ch. 5.5 - Water enters the tubes of a cold plate at 70F with...Ch. 5.5 - Prob. 96PCh. 5.5 - A computer cooled by a fan contains eight PCBs,...Ch. 5.5 - A desktop computer is to be cooled by a fan. The...Ch. 5.5 - Prob. 99PCh. 5.5 - A 4-m 5-m 6-m room is to be heated by an...Ch. 5.5 - A house has an electric heating system that...Ch. 5.5 - A long roll of 2-m-wide and 0.5-cm-thick 1-Mn...Ch. 5.5 - Prob. 103PCh. 5.5 - Prob. 104PCh. 5.5 - Argon steadily flows into a constant-pressure...Ch. 5.5 - Steam enters a long, horizontal pipe with an inlet...Ch. 5.5 - Refrigerant-134a enters the condenser of a...Ch. 5.5 - A hair dryer is basically a duct in which a few...Ch. 5.5 - A hair dryer is basically a duct in which a few...Ch. 5.5 - Air enters the duct of an air-conditioning system...Ch. 5.5 - An insulated rigid tank is initially evacuated. A...Ch. 5.5 - A rigid, insulated tank that is initially...Ch. 5.5 - Prob. 115PCh. 5.5 - A 2-m3 rigid tank initially contains air at 100...Ch. 5.5 - A 0.2-m3 rigid tank equipped with a pressure...Ch. 5.5 - Prob. 118PCh. 5.5 - An insulated 40-ft3 rigid tank contains air at 50...Ch. 5.5 - A 4-L pressure cooker has an operating pressure of...Ch. 5.5 - An air-conditioning system is to be filled from a...Ch. 5.5 - Oxygen is supplied to a medical facility from ten...Ch. 5.5 - A 0.05-m3 rigid tank initially contains...Ch. 5.5 - A 0.12-m3 rigid tank contains saturated...Ch. 5.5 - A 0.3-m3 rigid tank is filled with saturated...Ch. 5.5 - The air-release flap on a hot-air balloon is used...Ch. 5.5 - Prob. 127PCh. 5.5 - An insulated 0.15-m3 tank contains helium at 3 MPa...Ch. 5.5 - A vertical pistoncylinder device initially...Ch. 5.5 - A vertical piston-cylinder device initially...Ch. 5.5 - A pistoncylinder device initially contains 0.6 kg...Ch. 5.5 - The weighted piston of the device shown in Fig....Ch. 5.5 - Prob. 136RPCh. 5.5 - Prob. 137RPCh. 5.5 - Prob. 138RPCh. 5.5 - Air at 4.18 kg/m3 enters a nozzle that has an...Ch. 5.5 - Prob. 140RPCh. 5.5 - An air compressor compresses 15 L/s of air at 120...Ch. 5.5 - A steam turbine operates with 1.6 MPa and 350C...Ch. 5.5 - Refrigerant-134a enters an adiabatic compressor at...Ch. 5.5 - Prob. 144RPCh. 5.5 - Prob. 145RPCh. 5.5 - Prob. 146RPCh. 5.5 - Prob. 147RPCh. 5.5 - Steam enters a nozzle with a low velocity at 150C...Ch. 5.5 - Prob. 149RPCh. 5.5 - Prob. 150RPCh. 5.5 - Prob. 151RPCh. 5.5 - Prob. 152RPCh. 5.5 - Prob. 153RPCh. 5.5 - Cold water enters a steam generator at 20C and...Ch. 5.5 - An ideal gas expands in an adiabatic turbine from...Ch. 5.5 - Determine the power input for a compressor that...Ch. 5.5 - Prob. 157RPCh. 5.5 - Prob. 158RPCh. 5.5 - Prob. 159RPCh. 5.5 - Prob. 160RPCh. 5.5 - In a dairy plant, milk at 4C is pasteurized...Ch. 5.5 - Prob. 162RPCh. 5.5 - Prob. 163RPCh. 5.5 - Prob. 164RPCh. 5.5 - Prob. 165RPCh. 5.5 - Prob. 166RPCh. 5.5 - The average atmospheric pressure in Spokane,...Ch. 5.5 - The ventilating fan of the bathroom of a building...Ch. 5.5 - Prob. 169RPCh. 5.5 - Determine the rate of sensible heat loss from a...Ch. 5.5 - Prob. 171RPCh. 5.5 - An air-conditioning system requires airflow at the...Ch. 5.5 - A building with an internal volume of 400 m3 is to...Ch. 5.5 - The maximum flow rate of standard shower heads is...Ch. 5.5 - Prob. 176RPCh. 5.5 - Prob. 177RPCh. 5.5 - Steam enters a turbine steadily at 7 MPa and 600C...Ch. 5.5 - Reconsider Prob. 5178. Using appropriate software,...Ch. 5.5 - Prob. 180RPCh. 5.5 - A liquid R-134a bottle has an internal volume of...Ch. 5.5 - A pistoncylinder device initially contains 2 kg of...Ch. 5.5 - A pistoncylinder device initially contains 1.2 kg...Ch. 5.5 - A pressure cooker is a pot that cooks food much...Ch. 5.5 - A tank with an internal volume of 1 m3 contains...Ch. 5.5 - In a single-flash geothermal power plant,...Ch. 5.5 - An adiabatic air compressor is to be powered by a...Ch. 5.5 - The turbocharger of an internal combustion engine...Ch. 5.5 - Prob. 189RPCh. 5.5 - Consider an evacuated rigid bottle of volume V...Ch. 5.5 - An adiabatic heat exchanger is used to heat cold...Ch. 5.5 - A heat exchanger is used to heat cold water at 15C...Ch. 5.5 - An adiabatic heat exchanger is used to heat cold...Ch. 5.5 - In a shower, cold water at 10C flowing at a rate...Ch. 5.5 - Prob. 195FEPCh. 5.5 - Prob. 196FEPCh. 5.5 - Hot combustion gases (assumed to have the...Ch. 5.5 - Steam expands in a turbine from 4 MPa and 500C to...Ch. 5.5 - Steam is compressed by an adiabatic compressor...Ch. 5.5 - Refrigerant-134a is compressed by a compressor...Ch. 5.5 - Refrigerant-134a at 1.4 MPa and 70C is throttled...Ch. 5.5 - Prob. 202FEPCh. 5.5 - Prob. 203FEPCh. 5.5 - Air at 27C and 5 atm is throttled by a valve to 1...Ch. 5.5 - Steam at 1 MPa and 300C is throttled adiabatically...Ch. 5.5 - Air is to be heated steadily by an 8-kW electric...Ch. 5.5 - Saturated water vapor at 40C is to be condensed as...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 5000 kg of dry air per hour is cooled from 60 oC to 34 oC in a countercurrent heat exchanger. In the cooling process, the cold air supplied to the heat exchanger is used at a speed of 6200 kg/h and at 20 oC. If the same amount of hot air was cooled from 60 oC to 24 oC in a longer heat exchanger with the help of cold air under the same conditions, determine what the ratio of the new heat exchanger length to the original heat exchanger length would be (assume the specific heat of the air is constant).arrow_forwardWater flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is used to provide additional energy to the water between the two turbines. The first turbine has a power output of 8,000 kW. Determine the power output of the second turbine in kW and the process efficiency of each turbine. Determine the state of steam in turbine 1, Formulate the 1st Law for turbine 1, and solve for the flow rate of steam. Formulate the 1st Law for the heat exchanger, and solve for the temperature at exitarrow_forwardA diesel engine produces hot exhaust gases which are used to produce steam in an evaporator. The heat transfer surface area of the heat exchanger based on water side is 0.5 m² and overall heat transfer coefficient is 1780 W/m² °C. Exhaust gases (Cp = 1051 J/kg • °C) enter the heat exchanger at 550°C at a rate of 0.25 kg/s while water enters as saturated liquid and evaporates at 200°C. Determine the rate of evaporation of water in kg/hr. A 175 B 165 с 170 D 160arrow_forward
- In an heat exchanger of parallel flow type, water enters at 60°C and leaves at 80°C while oil of specific gravity 0.8 enters at 250°C and leaves at 100°C. The specific heat of oil is 2.5 kJ/kg K and surrounding temperature is 300 K. Determine the loss in availability on the basis of one kg of oil flow per second.arrow_forwardTwo products enter an indirect contact heat exchanger that uses steam for heating. The first product which contains 12% solids enters at the rate of 3 kg/hr and at 10 °C. The second stream which contains 20% solids enters at the rate of 4 kg/hr and at 20 °C. Saturated steam at 150 °C (hL = 2745.9 kJ/kg, hv = 632.25 k.J/kg) enters the heat exchanger at 0.5 kg/hr with a quality of 95% and exits at 10% quality. The resulting mixture enters an indirect contact cooler. Water enters the indirect contact cooler at a temperature of 10 °C and exits at 25 °C. Two product streams exit the cooler. The first stream contains 24% solids and exits at 2 kg/hr and at 10 °C, while the second stream exits at 12 °C. The specific heat of the solids is 3500 J/kg K and that of water is 4180 J/kg K. Complete/label the process diagram and determine the following: a. Specific heat of each stream b. Enthalpy of entering and exiting steam c. Temperature of the mixture exiting the indirect contact heat exchanger,…arrow_forwardAn adiabatic heat exchanger is used to heat cold water át 8 C entering at a rate of 3 kg/s by hot air at 150 C entering also at rate of 3 kg/s. If the exit temperature of hot air is 30 C, the exit temperature of cold water is which of the following: (use constant specific heats evaluated at 300 K). 128.4 C O28.6 C O 31.2 C 36.9 C O 149.7 Carrow_forward
- In a power plant steam, steam is continuously extracted from the turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1250 kJ/min from condensing steam and rejects waste heat to a lake at 20°C at a rate of 800 kJ/min. Determine the lowest possible condensing steam temperature.arrow_forwardSaturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 10 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. It is also know that the enthalpy of the water exiting the heat exchanger is 1718.2 kJ/kg. In the question that follows, select the answer that is closest to the true value. What is the quality of the water at the exit of the heat exchanger?arrow_forwardSaturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 5 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. In the question that follows, select the answer that is closest to the true value. What is the enthalpy of the water at the exit of the heat exchanger in units of kJ/kg?arrow_forward
- Water flows through a shower head steadily at the rate of 8 kg/min. The water is heated in an electric water heater from 150C to 450C. In an attempt to conserve energy, it is proposed to pass the drained warm water at a temperature of 380C through a heat exchanger to preheat the incoming cold water. Design a heat exchanger that is suitable for this task, and discuss the potential savings in energy.arrow_forwardSaturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 11 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. What is the enthalpy of the water at the exit of the heat exchanger in units of kJ/kg? Select the answer that is closest to the true value. A) 911 B) 1234 C) 1557 D) 1879 A Moving to another question will save this response. Question 1 of 11arrow_forwardSaturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 11 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. What is the enthalpy of the water at the exit of the heat exchanger in units of kJ/kg? Select the answer that is closest to the true value. A) 911 B) 1234 C) 1557 D) 1879 AMoving to another question will save this response. Question 1 of 11arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Heat Transfer [Conduction, Convection, and Radiation]; Author: Mike Sammartano;https://www.youtube.com/watch?v=kNZi12OV9Xc;License: Standard youtube license