Concept explainers
The final temperature and mass of the air in the ballast tank.
Answer to Problem 176RP
The final temperature and mass of the air in the ballast tank is
Explanation of Solution
Write the general mass balance equation.
Here, the inlet mass flow rate is
It is given that the mass of air pumped into the tank to get the submarine to the surface. Here, there is no exit mass of air. Thus, the exit mass
Refer Equation (I).
Write the mass balance equation for air.
Here, the subscript
While air entering into the ballast tank, the seawater present in the tank is released to the sea. Here, there is no inlet mass of water. Thus, the inlet mass
Refer Equation (I).
Write the mass balance equation for water.
Here, the subscript
Write the general energy rate balance equation.
Here, the rate of total energy in is
The system is at steady state. Hence, the rate of change in net energy of the system becomes zero.
Refer Equation (IV).
Write the energy balance equation for the system (ballast tank).
Here, the mass is
Substitute
Integrate the Equation (VI) at initial (1) and final (2) states.
The enthalpy and internal energy is expressed as follows.
The mass of air is expressed as follows.
Here, the specific volume is
For water the specific heat is
At final state, the mass sea water is zero and the ballast is completely filled with air.
Rewrite the Equation (VII) as follows.
Here,
The specific heat ratio is,
The initial and final pressure of air is,
Rewrite the Equation (VIII) as follows.
Write the formula for mass flow rate of air at final state.
Refer Table A-1, “Molar mass, gas constant, and critical-point properties”.
The gas constant
Refer Table A-2a, “Ideal-gas specific heats of various common gases”.
The specific heat ratio
Conclusion:
Substitute
Substitute
Thus, the final temperature and mass of the air in the ballast tank is
Want to see more full solutions like this?
Chapter 5 Solutions
THERMODYNAMICS-SI ED. EBOOK >I<
- What is the specific internal energy of water at 50 kPa and 200°C?arrow_forwardA piston cylinder contains 1.25 kg water at 25°C with a constant load on the piston such that the pressure is 300 kPa. A nozzle in a line to the cylinder is opened to enable flow to the outside atmosphere at 100 kPa and 25°C. The process continues until 85% of the initial mass has flowed out. At this point, the temperature of water increased by 10℃. Assume that the process is done in an isobaric manner. Write the mass and energy balance equations and calculate the work (kJ) and heat (kJ) involved in the process if the exit velocity is 40 m/s. For compressed liquid, assume the substance is a saturated liquid at the giventemperature.arrow_forwardA partition divides an insulated tank into two parts which are not equal. One part of the tank contains 5 kg of compressed liquid water at 65°C and 600 kPa while the other part is evacuated (Hint: For compressed liquids, if tables are not available, use properties of the saturated liquid at the specified temperature). The partition is then removed, and the water expands to fill the entire tank. Determine the final temperature of the water and the volume of the tank for a final pressure of 20 kPa.arrow_forward
- A 0.08-m rigid tank initially contains saturated water vapor at 180 °C. The tank is connected by a valve to a supply line that carries steam at 1400 kPa and 400 °C. Now the valve is opened, and steam is allowed to enter the tank. Heat transfer takes place with the surroundings such that the temperature in the tank remains constant at 180 °C at all times. The valve is closed when it is observed that one-third of the volume of the tank is occupied by liquid water. Find (a) the amount of steam that has entered the tank, and (b) the amount of heat transfer. 1400 kPa Steam 400°C Saturated vapor Qout V=0.08 m T, = 180°Carrow_forwardFive hundred kilograms per hour of steam moves a turbine. The steam enters the turbine at 44 atm and 450°C with a speed linear 60 m/s, and exits at a point 5 m below the inlet, at pressure atmospheric and at a speed of 360 m/s. The turbine provides work on the shaft with a rating of 70 kW, and the heat loss in the turbine is estimated at 104 kcal/h. Calculate the variation in specific enthalpy associated with the process.arrow_forwardHi! A 14-ft3 tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is rotated until the pressure inside rises to 20 psia. During the process 20 Btu of heat is lost to the surroundings. Determine the paddle-wheel work done. Neglect the energy stored in the paddle wheel. The gas constant and molar mass of oxygen are R = 0.3353 psia·ft3/lbm·R and M = 32 lbm/lbmol. The specific heat of oxygen at the average temperature of Tavg = (735 + 540)/2 = 638 R is cv ,avg= 0.160 Btu/lbm·R. The paddle-wheel work done is Btu. ANSWERarrow_forward
- Water is heated with the aid of a diesel furnace. 2kg of diesel fuel is required for every 300 litres of water. If the heat transfer efficiency is 85%, determine the final temperature of the water. The initial temperature of the water is 200C. assume the calorific heat value of diesel to be 31,5MJ/kg.arrow_forwardSup A 14-ft3 tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is rotated until the pressure inside rises to 20 psia. During the process 20 Btu of heat is lost to the surroundings. Determine the paddle-wheel work done. Neglect the energy stored in the paddle wheel. The gas constant and molar mass of oxygen are R = 0.3353 psia·ft3/lbm·R and M = 32 lbm/lbmol. The specific heat of oxygen at the average temperature of Tavg = (735 + 540)/2 = 638 R is cv ,avg= 0.160 Btu/lbm·R. The paddle-wheel work done is Btu. ANSWER is not 54 or 72arrow_forwardLiquid water at 200 kPa and 20 degress celcius is heated in a chamber by mixing it with superheated steam at 200 kPa and 250 degrees celcius. Liquid water enters the mixing chamber at a rate of 4.2 kg/s, and the chamber is estimated to lose heat to the surrounding air at 23 degress celcius at a rate of 1200 kJ/min. If the mixture leaves the mixing chamber at 200 kPa and 85 degrees celcius determine (a) the mass flow rate of the superheated steam, and (b) the rate of entropy generation during the mixing process.arrow_forward
- Steam is accelerated by a nozzle at a steady mass flow rate of 2 kg/s. If the steam at the nozzle exit is at 400°C and 3 MPa, and its velocity is 180 m/s, what is the exit area of the nozzle? If the velocity at the inlet of the nozzle is 80 m/s, what is the enthalpy of the steam at the inlet?arrow_forwardSubmarines change their depth by adding or removing air from rigid ballast tanks, thereby displacing seawater in the tanks. Consider a submarine that has a 700-m³ air-ballast tank originally partially filled with 100 m³ of air at 1550 kPa and 15°C. For the submarine to surface, air at 1550 kPa and 20°C is pumped into the ballast tank until it is entirely filled with air. The seawater leaves the tank at 15°C. Presume that air is added to the tank in such a way that the temperature and pressure of the air in the tank remain constant. Determine the final mass of the air in the ballast tank under this condition. Also determine the total heat transfer while the tank is being filled in this manner. The gas constant of air is R = 0.287 kPa.m³/kg.K. The specific heats of air at room temperature are cp= 1.005 kJ/kg-K and cv = 0.718 kJ/kg-K. The specific volume of water is taken 0.001 m³/kg. The final mass of the air in the ballast tank is The total heat transfer is kJ. kg.arrow_forwardIn a boiler of a steam power plant the incoming water is heated to steam by hot gas flowing around the tube. The hot gas is produced by combustion of coal. Consider the pressure of water flowing through the tube to be 4 MPa. Water enters the tube at a velocity of 0.1 m/s and a temperature of 50 °C. The tube diameter is 2.5 cm. The hot gas flowing around the tube is at 1000 °C. The water needs to reach the saturation temperature of 250 °C. Assuming bulk mean temperature of water to be 600 °C, and the determine the average convective heat transfer coefficient to be 80 W/m².K, determine what should be the length of the pipe.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY