Explanation Sign conversion: Apply the sign convention for calculating the equations of equilibrium as below. For the horizontal forces equilibrium condition, take the force acting towards right side as positive ( → + ) and the force acting towards left side as negative ( ← − ) . For the vertical forces equilibrium condition, take the upward force as positive ( ↑ + ) and downward force as negative ( ↓ − ) . For moment equilibrium condition, take the clockwise moment as negative and counter clockwise moment as positive. Apply the following sign convention for calculating the axial forces, shear and bending moments. When the portion of the beam considered is left of the section, then the external force acting to the left are considered as positive. When the portion of the beam considered is right of the section, then the external force acting to the right are considered as positive. When the portion of the beam considered is left of the section, then the external force acting upward are considered as positive. When the portion of the beam considered is right of the section, then the external force acting downward are considered as positive. When the portion of the beam considered is left of the section, then the clockwise moments are considered as positive. When the portion of the beam considered is right of the section, then the counterclockwise moments are considered as positive. Calculation: Show the free-body diagram of the entire beam as in Figure 1. Find the horizontal reaction at point C by resolving the horizontal equilibrium. + → ∑ F y = 0 − C y + 1 2 × 4.5 × 36 = 0 C y = 81 k ← Find the vertical reaction at point C by resolving the vertical equilibrium. + ↑ ∑ F x = 0 C x = 0 Find the moment at point C by taking moment about the point C . + ↺ ∑ M C = 0 − 1 2 × 4.5 × 36 × ( 1 3 × 36 ) + M C = 0 M C = 972 k-ft Pass the sections aa and bb at points A and B respectively. Show the sections aa and bb as in Figure 2. Consider section aa : Consider the upper side of the section aa for calculation of internal forces. Show the free-body diagram of the upper side of the section aa as in Figure 3. Find the axial force at point A by resolving the vertical equilibrium. + ↓ ∑ F x = 0 Q A = 0 Find the shear at point A by resolving the horizontal equilibrium

6th Edition

ISBN: 9781337630931

Author: KASSIMALI, Aslam.

Publisher: Cengage,

See similar textbooks

Question

Chapter 5, Problem 6P

To determine

Find the axial force, shear, and bending moment at points A and B of the beam.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 5, Problem 5P

Chapter 5, Problem 7P

Students have asked these similar questions

Q2- For the retaining wall shown in the figure, calculate the magnitude and resultant, of active thrust and calculate only the magnitude of passive thrust. q = 10kN/m² 不 2 m y-18 kN/m³ 0=35° C=0 * 2 m y=18 kN/m³ 0=20° 6 m C=15 kN/m² y=18 kN/m³ 0-20° C=15 kN/m² 2

أ. ما هي شروط حديد التسليح المستخدم في موقع العمل بشكل عام وكيف يجب ان يكون ؟ ب. كم حلقة تحتاج لاساس شريطي طوله 40 مترا اذا كان مكتوب في المخطط ( mm 300 @ 010) ؟ B - لمقطع الأساس الشريطي ادناه، احسب كمية الحديد الطولي السفلي والمواد الانشائية المطلوبة ) سمنت ، رمل ، حصى ( لكل 30 متر طول منه ونسب الخلط 1:3:5 اذا كان حديد التسليح المتوفر طول 9 متر . (15) درجة ) 3014 $10@200mm 4016 800mm A 400mm جدول اوزان حديد اتسليح قطر الشيش (mm) كتلة الشيش (kg/m) 0.222 6 0.395 8 0.617 10 0.888 12 1.21 14 1.58 16 2 18 2.47 20 3.86 25

A4.2- Develop the column interaction diagram for a tied short column, shown in Figure 2. Given: f'c = 35 MPa fy = 400 MPa Longitudinal bars: 8-35M Ties: 10M@ 300 Clear cover to the ties: 40mm T 500 mm 500 mm Figure 2

Chapter 5 Solutions

Structural Analysis

Ch. 5 - Prob. 1P Ch. 5 - Prob. 2P Ch. 5 - Prob. 3P Ch. 5 - Prob. 4P Ch. 5 - Prob. 5P Ch. 5 - Prob. 6P Ch. 5 - Prob. 7P Ch. 5 - Prob. 8P Ch. 5 - Prob. 9P Ch. 5 - Prob. 10P

Knowledge Booster