Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 5ASRQ
Technician A says that delayed shifting can be caused by worn planetary gearset members. Technician B says that delayed shifts or slippage may be caused by leaking hydraulic circuits or sticking spool valves in the valve body. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have shiftinf problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct?
a.Technician A only
b.Technician B only
c. both A and B
d. Neither A or nor B.
When discussing shift problems,
Technician A says that worn or broken engine and
transaxle mounts can cause a transaxle to have
shifting problems.
Technician B that poor shift boot alignment
can cause a transaxle to jump out of gear.
says
Who is correct?
A. A only
C. Both A and B
B. B only
D. Neither A nor B
When discussing the possible causes for a shudder during acceleration,
Technician A says that a worn inner CV joint could be the cause.
Technician B says that insufficient differential gear backlash could be the cause of the problem.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
Chapter 43 Solutions
Automotive Technology
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - List five reasons for replacing a torque...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - What is checked during a stall test?Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What should you do if a valve does not move freely...
Ch. 43 - Which of the following is the most likely cause...Ch. 43 - When should the ATF level be checked on most...Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that negative caster provides directional stability . Technician B says that pos caster results from excessive positive cam ber . Who is correct ?arrow_forwardA car jumps out of gear into neutral, particularlywhen decelerating or going down hills: Technician Achecks the shift lever and external gearshift linkagefirst. Technician B says that the clutch pilot bearingcould be the problem. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardWhile discussing the possible causes for damage to the surface of a pressure plate.Technician A says a worn clutch disc can score the surface. Technician B saysinsufficient pedal free travel can cause it to overheat. Who is correct?a. Technician Ac. Both A and Bb. Technician Bd. Neither A nor Barrow_forward
- Technician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forwardTechnician A says that shift solenoids direct fluid flow to and away from the apply devices in the transmission. Technician B says that shift solenoids are used to mechanically apply a friction brake or multiple-disc clutch assembly. Who is correct?arrow_forwardvehicle is producing a sharp, metallic rappingsound originating in the upper portion of the engine.It is most noticeable during idle. Technician A diagnosesthe problem as piston pin knock. Technician Bsays that the problem is most likely a loose crankshaftthrust bearing. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forward
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. Falsearrow_forwardTechnician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forwardTech A states to check the camshaft for lift, the cam must be removed from the engine. Tech B says to check for a bent camshaft, the cam must be removed and placed onto a set of V-blocks and checked with a dial indicator. Who is correct?arrow_forward
- Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket. Who is correct? and why? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage. Tech b smoothens a damaged camshaft or balance shaft journal by lightly sanding it. Who is correct?arrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License