Concept explainers
For the boom and loading shown, determine (a) the tension in cord BD, (b) the reaction at C.
Fig.P4.71
(a)
The tension in the cord
Answer to Problem 4.71P
The tension in the cord
Explanation of Solution
Calculation:
If the rigid body subjected to three forces, such a body is commonly called a three-force body. If a two force body is in equilibrium the lines of action of the three forces must be either concurrent or parallel.
The figure 1 represents the free body diagram of the system.
Write the expression for the angle
Here,
Write the expression for the angle
Write the relations connecting the sides of the triangle.
Figure 2 represents a force triangle as shown in the above figure with its interior angles computed from the known directions of the forces. Then use the law of sines to find the unknown forces.
Write the expression for the law of sines from the force triangle.
Conclusion:
Substitute
Substitute
Substitute
Substitute
On rearranging the above equation to find
Therefore, the tension in the cord
(b)
The reaction at
Answer to Problem 4.71P
The reaction at
Explanation of Solution
Calculation:
If the rigid body subjected to three forces, such a body is commonly called a three-force body. If a two force body is in equilibrium the lines of action of the three forces must be either concurrent or parallel.
Write the expression for the angle
Here,
Write the expression for the angle
Write the relations connecting the sides of the triangle.
Figure 2 represents a force triangle as shown in the above figure with its interior angles computed from the known directions of the forces. Then use the law of sines to find the unknown forces.
Write the expression for the law of sines from the force triangle.
Conclusion:
Substitute
Substitute
Substitute
Substitute
On rearranging the above equation to find
Therefore, reaction at
Want to see more full solutions like this?
Chapter 4 Solutions
VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS
- Vector Mechanics for Engineers (EIT Review) Problem 4.34 Neglecting friction and the radius of the pulley, determine (a) the tension in cable ADB, (b) the reaction at C. A 8 in. Fig. P4.34 30 lb 8 in. B 20 in.- D 15 in.arrow_forwardAnswer the given problem. Show your complete solution. Provide a handwritten calculationarrow_forwardFor the bracket and loading shown, determine the range of values of the distance a for which the magnitude of the reaction at B does not exceed 600 N.Fig P4.62arrow_forward
- 1. Two tape spools are attached to an axle supported by bearings at A and D. Assume that the bearing at A does not exert any axial thrust. The radius of spool B is 1.5 in and the radius of spool C is 2 in. Knowing that TB = 20 lb., determine (a) the tension, Tc, and (b) the reactions at A and D. 4.5 in. A TC 6 in. B 4.5 in. Ans: Tc = 15 lb, A= 0î +14 j+4.5k lb D = 0î +6j+10.5k lb Darrow_forwardThe assembly shown is used to control the tension T in a tape that passes around a frictionless spool at E. Collar C is welded to rods ABC and CDE . It can rotate about shaft FG but its motion along the shaft is prevented by a washer S . For the loading shown, determine (a) the tension T in the tape, (b) the reaction at C.arrow_forwardFor the frame and loading shown, determine the reactions at C and D. 150 lb A -3 ft Fig. P4.68 B -3 ft D 1.5 ft 15 ftarrow_forward
- Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D. The radius of the inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension is 120 N in both portions of belt B and 180 N in both portions of belt C, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust. 150 mm 100 mm 200 mm Tc T'. T'B OD= (60.0 N) j + (166.7 N) k OD = (166.7 N) j + (60.0 N) k O D = (80.0 N) j+ (200.0 N) k OD = (200.0 N) j + (80.0 N) k O D = (100.0 N) j + (240.0 N) k OD = (240.0 N) j+ (100.0 N) karrow_forwardA force P of magnitude 120 tb is applied to member ACE, which is supported by a frictionless pin at Dand by the cable ABE. Since the cable passes over a small þulley at B, the tension may be assumed to be the same in portions AB and BE of the cable. For the case when a = 3 in., determine (a) the tension in the cable, (b) the reaction at D 12 in. A -5 in. a. T= 156.5 (b, 429.8 lb b. T= 17.4 lb, D = 129.8 lb C. T= 117.4 lb, D = 144.5 tb %3D d. T= 156.5 b, D = 174.0 1barrow_forwardTwo transmission belts pass over pulleys welded to a shaftwhich is supported by bearings at B and D. If the pulley at A has a radius of 2.5 in., and the pulley at C has a radius of 2 in. and it is known that the system rotates with a constant angular velocity, determine a) the tension T, b) the reactions at B and D. Suppose that the bearing at D does not exert any axial thrust force and does not take into account the weights of pulleys and shaftarrow_forward
- A thin ring of mass 2 kg and radius r=140 mm is held against a frictionless wall by a 125-mm string AB. Determine (a) the distance d, (b) the tension in the string, (c) the reaction at C.arrow_forwardItranscript Two transmission belts pass over a double-sheaved pulley that is attached to an axle supported by bearings at A and D. The radius of the Inner sheave is 125 mm and the radius of the outer sheave is 250 mm. Knowing that when the system is at rest, the tension Is 98 N In both portions of belt B and 158 N In both portions of belt C, determine the reactions at A and D. Assume that the bearing at D does not exert any axial thrust. 150 mm 100 mm TB The reaction at A Is ( The reaction at D Is T's |N)J + NJ 200 mm N)k. N)k. Tc T'carrow_forwardFor the boom and loading shown, determine (a) the tension in cord BD, (b) the reaction at C.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY