Explanation Given information: The length of the boom is 2.4 m . The 3.6 kN load applied at A . Calculation: Assumption: Apply the sign convention for calculating the equations of equilibrium as shown below. For the horizontal forces equilibrium condition, take the force acting towards right side as positive ( → + ) and the force acting towards left side as negative ( ← − ) . For the vertical forces equilibrium condition, take the upward force as positive ( ↑ + ) and the downward force as negative ( ↓ − ) . For moment equilibrium condition, take the clockwise moment as negative and counterclockwise moment as positive. Draw the free body diagram of the assembly as in Figure (1). Refer Figure (1). Calculate the position vector ( r ) as shown below. The position of A is r A = ( 2.4 m ) k . The position of B is r B = ( 1.2 m ) k . The position of D is r D = − ( 0.8 m ) i + ( 0.6 m ) j . The position of E is r E = ( 0.8 m ) i + ( 1.2 m ) j . Calculate the position of cable AD as shown below. A D → = r D − r A Substitute − ( 0.8 m ) i + ( 0.6 m ) j for r D and ( 2.4 m ) k for r A . A D → = [ − ( 0.8 m ) i + ( 0.6 m ) j ] − [ ( 2.4 m ) k ] = − ( 0.8 m ) i + ( 0.6 m ) j − ( 2.4 m ) k Calculate the length of cable AD as shown below. A D = ( − 0.8 ) 2 + ( 0.6 ) 2 + ( − 2.4 ) 2 = 6.76 = 2.6 m Calculate the position of cable AE as shown below. A E = r E − r A Substitute ( 0.8 m ) i + ( 1.2 m ) j for r E and ( 2.4 m ) k for r A . A E = [ ( 0.8 m ) i + ( 1.2 m ) j ] − [ ( 2.4 m ) k ] = ( 0.8 m ) i + ( 1.2 m ) j − ( 2.4 m ) k Calculate the length of cable AE as shown below. A E = ( 0.8 ) 2 + ( 1.2 ) 2 + ( − 2.4 ) 2 = 7.84 = 2.8 m Calculate the tension in cable AD ( T A D ) as shown below. T A D = T A D A D → A D Substitute − ( 0.8 m ) i + ( 0.6 m ) j − ( 2.4 m ) k for A D → and 2.6 m for A D . T A D = T A D − 0.8 i + 0.6 j − 2.4 k 2.6 = T A D 2.6 ( − 0.8 i + 0.6 j − 2.4 k ) Calculate the tension in cable AE ( T A E ) as shown below. T A E = T A E A E → A E Substitute ( 0.8 m ) i + ( 1.2 m ) j − ( 2.4 m ) k for A E → and 2.8 m for A E . T A E = T A E 0.8 i + 1.2 j − 2.4 k 2.8 = T A E 2.8 ( 0.8 i + 1.2 j − 2.4 k ) Apply the Equations of Equilibrium as shown below. Apply the Equilibrium equation of moment about point C and equate to zero for equilibrium. ∑ M C = 0 r A × T A D + r A × T A E + r A × ( − 3 j ) = 0 Substitute ( 2.4 m ) k for r A , T A D 2.6 ( − 0.8 i + 0.6 j − 2.4 k ) for T A D , and T A E 2.8 ( 0

11th Edition

ISBN: 9781259633133

Author: BEER

Publisher: MCG

See similar textbooks

Question

Chapter 4.3, Problem 4.109P

To determine

The tension in each cable and the reaction at C.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 4.3, Problem 4.108P

Chapter 4.3, Problem 4.110P

Students have asked these similar questions

First monthly exam Gas dynamics Third stage Q1/Water at 15° C flow through a 300 mm diameter riveted steel pipe, E-3 mm with a head loss of 6 m in 300 m length. Determine the flow rate in pipe. Use moody chart. Q2/ Assume a car's exhaust system can be approximated as 14 ft long and 0.125 ft-diameter cast-iron pipe ( = 0.00085 ft) with the equivalent of (6) regular 90° flanged elbows (KL = 0.3) and a muffler. The muffler acts as a resistor with a loss coefficient of KL= 8.5. Determine the pressure at the beginning of the exhaust system (pl) if the flowrate is 0.10 cfs, and the exhaust has the same properties as air.(p = 1.74 × 10-3 slug/ft³, u= 4.7 x 10-7 lb.s/ft²) Use moody chart (1) MIDAS Kel=0.3 Q3/Liquid ammonia at -20°C is flowing through a 30 m long section of a 5 mm diameter copper tube(e = 1.5 × 10-6 m) at a rate of 0.15 kg/s. Determine the pressure drop and the head losses. .μ= 2.36 × 10-4 kg/m.s)p = 665.1 kg/m³

2/Y Y+1 2Cp Q1/ Show that Cda Az x P1 mactual Cdf Af R/T₁ 2pf(P1-P2-zxgxpf) Q2/ A simple jet carburetor has to supply 5 Kg of air per minute. The air is at a pressure of 1.013 bar and a temperature of 27 °C. Calculate the throat diameter of the choke for air flow velocity of 90 m/sec. Take velocity coefficient to be 0.8. Assume isentropic flow and the flow to be compressible. Quiz/ Determine the air-fuel ratio supplied at 5000 m altitude by a carburetor which is adjusted to give an air-fuel ratio of 14:1 at sea level where air temperature is 27 °C and pressure is 1.013 bar. The temperature of air decreases with altitude as given by the expression The air pressure decreases with altitude as per relation h = 19200 log10 (1.013), where P is in bar. State any assumptions made. t = ts P 0.0065h

36 2) Use the method of MEMBERS to determine the true magnitude and direction of the forces in members1 and 2 of the frame shown below in Fig 3.2. 300lbs/ft member-1 member-2 30° Fig 3.2. https://brightspace.cuny.edu/d21/le/content/433117/viewContent/29873977/View

Chapter 4 Solutions

VECTOR MECH...,STAT.+DYNA.(LL)-W/ACCESS

Ch. 4.1 - Two crates, each of mass 350 kg, are placed as...Ch. 4.1 - A lever AB is hinged at C and attached to a...Ch. 4.1 - A light rod AD is supported by frictionless pegs...Ch. 4.1 - A tension of 20 N is maintained in a tape as it...Ch. 4.1 - A gardener uses a 60 N wheelbarrow to transport a...Ch. 4.1 - The gardener of Prob. 4.1 wishes to transport a...Ch. 4.1 - A 2100-lb tractor is used to lift 900 lb of grave....Ch. 4.1 - For the beam and loading shown, determine (a) the...Ch. 4.1 - A load of lumber of weight W = 25 kN is being...Ch. 4.1 - A load of lumber of weight W = 25 kN is being...

Knowledge Booster

The tension in each cable and the reaction at C .

The tension in each cable and the reaction at C.

Want to see the full answer?

Chapter 4 Solutions